Table of Contents
Advertisement
.
:..:
'
:
,..,.:f,
.
:
.;
.,:.
'
!
.
.
. 1
__..._
L.
..
.
...
.
. .
...
. .....
..
. .
.
..... ".
,
._..
. .
,
.
.
, .
..
,
Capacities
Steel
Wood
Wood screw
Machine screw
10mm
21mm
5 . 8 m m x 7 5 m m
6 m m
1318")
113/16'J
115164" x 2-5/16")
115/64"l
, ,
.
....
"
!.
No load speed IRPMI
Dimensions
Net
1 1 x W x HJ
270 mm x 58 mm x 262 mm
weight
High
Low
1.9 kg
-
1'350
-
450
110-5/8"
x
2-114" x 10-5/16"1
14.2 lbsl
Equipped with
Keyless
Chuck and Electric Brake
MODEL 6 O l l D
MODEL 6011DW
Wlth Fast Charger
INSTRUCTION MANUAL
Voltage
SPECIFICATIONS
9
Model 8011D
Charging time
Input
Output
I
I
12
v
1 HI.
A.C. only 50 HZ
-
60 Hz
I
D.C. 9.6 V. 12 V
Manufacturer reserves the right to change specifications without notice.
Note: Specifications may differ from country
to
country.
Advertisement
Table of Contents
Related Manuals for Makita 6011D
Summary of Contents for Makita 6011D
- Page 1 :..: ,..,.:f, __..._ .,:.... ". ._.." Equipped with Chuck and Electric Brake Keyless MODEL 6 O l l D MODEL 6011DW Wlth Fast Charger INSTRUCTION MANUAL SPECIFICATIONS Model 8011D Capacities No load speed IRPMI Dimensions 1 1 x W x HJ weight Steel...
- Page 2 IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. WORK CONSIDER AREA ENVIRONMENT.
- Page 3 REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging 16.
- Page 4 1200, CAUTION To reduce risk injury, charge only MAKITA Battery 1 2 1 0 , 9000 9100. Other ty,pes of batteries may burst causing personal injury and damage. Do not expose charger t o rain or snow.
- Page 5 ..-. , r . _... ! _ . _ . . I : : . ..,r..ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) 4OoC ( 1 0 4 O F ) .
- Page 6 battery Installing or removing cartridge *Always switch off the tool before insertion or removal the battery cartridge. *To remove the battery cartridge, pull out Set plete the set plate on the tool and grasp both sides of the cartridge while withdrawing from the tool.
- Page 7 Installing or removing driver bit or dirll bit CAUTION : Always be sure that the tool i s switched off and the battery cartridge i s removed before installing or removing the bit. Hold the ring and turn the sleeve counter- clockwise to open the chuck jaws.
- Page 8 Speed change To change the speed, turn the speed change knob 180' while the tool is running. Be Speed change knob sure that the speed change knob is turned 450 Rlmin. to the correct speed setting before you 1,350 Rlmin. begin operation.
- Page 9 Always be sure that the tool is switched off and the battery cartridge removed before attempting to perform inspection or maintenance. maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
- Page 10 ACC ESSO R I ES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner.
-
Page 11: Cordless Driver Drill
F e b - 0 4 - ' 9 2 CORDLESS DRIVER DRILL Model 6011D... - Page 12 SEQUENTIAL DAMAGES FROM THE SALT OR USE O F THE PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THETERM O F THIS WARRANTY. MAKITA DISCLAIMS L l A B l L l N FOR ANY IMPLIED WARRANTIES. INCLUDING IMPLIED WARRANTIES O F "MERCHANTABILITY"...