Table of Contents
Advertisement
Installatio
Instructi
Free-Standin
ctric Ran es
[=_ Questions?
Call 800.GE.CARES
(800.432.2737)
or Visit our Website
at: go.corn
I
BEFORE YOU BEGIN
Read these
instructions
completely
and carefully.
• iMPORTANT - Save t hese
instructions
for local
inspector's
use.
• iMPORTANT
- Observe all
governing
codes
and ordinances.
• Note to Installer
- Be sure to leave these
instructions
with
the Consumer.
• Note to Consumer
- Keep these
instructions
for future
reference.
• Skill
level - installation
of this appliance
requires
basic mechanical
skills.
• Completion
time
- 1 to 3 hours
• Proper
installation
is the responsibility
of
the installer.
• Product
failure
due to improper
installation
is not covered
under
the Warranty.
-&WARNING
-
This appliance
must
be properly
grounded.
ANTI-TIP
DEVICE
-&WARNING - Toreduce therisk
of tipping,
the appliance
must
be secured
by
properly
installed
Anti-Tip
bracket
packed
with
this appliance.
If the Anti-Tip
device
supplied
with
the range
does
not fit this application,
use the universal
Anti-Tip
device
WB2X7909.
-&WARNING -
• All ranges can tip
• Injury to persons
could result
(_
• Install Anti-Tip
bracket
packed
with
range
• See Installation
Instructions
If you pull the range
out and away from
the
wall
for any reason,
make sure the Anti-Tip
bracket
is engaged
when
the range
is pushed
back against
the wall.
FOR YOUR SAFETY:
-&WARNING
-
Before
beginning
the
installation,
switch
power
off at service
panel
and lock the service
disconnecting
means
to
prevent
power
from
being
switched
on
accidentally.
When
the service
disconnecting
means
cannot
be locked,
securely
fasten
a
prominent
warning
device,
such as a tag, to
the service
panel.
31-10620-1
11-06 JR
Advertisement
Table of Contents
Related Manuals for GE JB988BK6BB
Summary of Contents for GE JB988BK6BB
- Page 1 Installatio Free-Standin Instructi ctric Ran es [=_ Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: go.corn BEFORE YOU BEGIN ANTI-TIP DEVICE -&WARNING - Toreduce therisk Read these instructions completely and carefully. of tipping, the appliance must be secured • iMPORTANT - Save t hese...
-
Page 2: Prepare To Install The Range
Installation instructions PREPARE TO INSTALL THE RANGE FOR YOUR SAFETY: MATERIALS YOU MAY NEED All rough-in and spacing dimensions must met for safe use of your range. On ranges with storage drawers electricity can be disconnected at the outlet without moving Tin Snips Lag Bolts... -
Page 3: Prepare The Opening
Installation instructions PREPARE THE OPENING See illustrations for all rough-in and spacing dimensions. The range may be placed with 0" clearance (flush) at the back wall and side walls the cabinet. *'15" Min. Acceptable electrical outlet area. Orient the electrical receptacle so the length _-25. -
Page 4: Electrical Connections
Installation Instructions ELECTRICAL CONNECTIONS ELECTRICAL REQUIREMENTS You must use a 3-wire, single-phase A.C. 208Y/120 Volt or 240/120 Volt, 60 hertz CAUTION: electrical system. For personal safety, do not use an extension cord with this If the electrical service provided does not appliance. -
Page 5: Power Cord And Strain Relief Installation
Installation instructions POWER CORD AND For power cord installations only (see the next step if using conduit), assemble STRAIN RELIEF INSTALLATION the strain relief in the hole. Insert power cord through the strain relief Remove the wire cover (on the back of tighten. - Page 6 Installation Instructions ELECTRICAL CONNECTIONS (CONT.) 3-WIRE POWER CORD 4-WIRE POWER CORD INSTALLATION INSTALLATION WARNING: WARNING: The neutral or ground The neutralwire wire of the power cord must be connected the supply circuit must be connected to the to the neutral terminal located in the neutral terminal located in the lower center center of the terminal...
- Page 7 Installation instructions 3-WIRE CONDUIT INSTALLATION 4-WIRE CONDUIT INSTALLATION Loosen the 3 lower terminal screws from Loosen the three lower terminal screws the terminal block. Insert the center bare from the terminal block. Remove the ground wire (white/neutral) tip through the bottom screw and ground plate and retain them.
-
Page 8: Install The Range
Installation Instructions INSTALL THE RANGE PREPARE TO LEVEL MODELS REPLACE THE WIRE COVER WITH BAKING OR WARMING Replace the wire cover on the range back DRAWERS by sliding its left edge under the retaining tabs and replacing the five screws removed Measure the height of your... - Page 9 Installation Instructions LEVEL THE RANGE FINAL INSTALLATION CHECKLIST Install the oven shelves in the oven and position the range where it will be installed. Check to make sure the circuit breaker closed (RESET) or the circuit fuses Check for levelness replaced.
- Page 10 Notes...
- Page 11 Notes...
- Page 12 Printed in the United States...