Installation Instructions - VALERA 533.03 Instructions For Use And Installation
Hairdryer - wall holder
Hide thumbs
Also See for 533.03:
- Instructions for use and installation (63 pages) ,
- Instructions for use manual (97 pages)
Table of Contents
Advertisement
Available languages
Available languages
INSTALLATION INSTRUCTIONS
Wall holder for hairdryer
Models 037C - 037M - 037R - 037S
Model 037C
Model with digital clock.
Model 037M
Model with magnifying mirror.
Model 037R
Model with universal shaver socket. A safety transformer
insulates the shaver socket from the mains and a protection
device inhibits the operation of appliances with a load higher than
20VA.
Model 037S
Model with standard European socket 2P + earthing 16A.
Installation of wall holder
This hair dryer must only be installed by a qualified electrician in
conformity to applicable safety standards. The hairdryer must be
fixed out of reach of a person using a bath or shower.
For each pole a switch with a minimum break distance between
contacts of 3 mm must be fitted up-line of the appliance.
Each time the appliance is opened, the switch must be used to
disconnect the appliance.
Method A
The connection wiring from the mains must be at least 3x1,5
mm
2
for wall holder model 037S.
The connection wiring from the mains must be at least 2x1,0
mm
2
for wall holder models 037R, 037C, 037M.
1. To fix the back of the wall unit to the wall, drill three holes for
the fixing screws and insert the relevant wall plugs (fig. 1).
2. Screw in screws (1) and (2) (fig. 2) first, leaving them
protruding at least 10 mm from the wall plugs.
3. Unscrew the screw (4) (fig. 3a) and remove the cover from
the wall unit.
4. Break the plastic membrane (5) at the back of the wall unit (fig. 4).
5. Route the main power cable from the wall (6) through the hole
left by the plastic membrane (5) (fig. 4).
6. Hang the wall unit over the two screws (1) and (2) and fully
tighten them (fig. 5).
7. Fully fix the unit to the wall with the last screw (3) (fig. 6).
8. Remove the terminal strip (7). Connect up the power cable (6)
and reposition the terminal strip. Tighten the cable clamp (8)
with its own screws. See fig. 7 for the specific model you
have purchased.
9. Models 037R, 037C and 037M are double insulated and do
not require grounding (earthing). Model 037S is fitted with a
European standard plug. The ground (earth) wire of the mains
supply must be connected to terminal (7). On this model it is
also important to check that the mains power supply is
suitable for a 16A load.
10. Remove the terminal strip (13). The power cable (11) of a
hairdryer with max input current of 10A, if not already
connected, must be connected to the terminal strip (13);
reposition the terminal strip(13) and tighten the cable clamp
(12) with its own screws.
11. Fit the cover back on the wall unit with (4) (fig. 3b).
12. Switch the power on at the mains switch. The hair dryer is
now ready to use.
Method B
The connection wiring must be at least type H05VV-F 2x1,0 mm
1. To fix the back of the wall unit to the wall, drill three holes for the
fixing screws and insert the relevant wall plugs (fig. 1).
2. Screw in screws (1) and (2) (fig. 2) first, leaving them protruding
at least 10 mm from the wall plugs.
3. Unscrew the screw (4) (fig. 3a) and remove the cover from the
wall unit.
4. Route the main power cable (9) through hole (10) (fig. 8).
5. Remove the terminal strip (7). Connect the power cable to the
mains (9) and reposition the terminal strip. Tighten the cable
clamp (8) with its own screws. See fig. 7 for the specific model
you have purchased.
6. Attention: this appliance is double insulated and no earth
connection is provided.
7. Remove the terminal strip (13). The power cable (11) of a
hairdryer with max input current of 10A, if not already
connected, must be connected to the terminal strip (13);
reposition the terminal strip(13) and tighten the cable clamp (12)
with its own screws.
8. Fit the cover back on the wall unit with (4) (fig. 3b).
9. Switch on the general switch of your mains electricity.
The hairdryer is ready for use.
INSTRUCTIONS FOR USE
Hairdryer with wall holder
Control Switches
0-1 = Off/On
Hairdryer
Mod. 533.03 - 533.05 - 533.03/I, - 533.05/I
Pushbutton:
ON=On/Off
(pressure must be maintained to operate the hairdryer)
Slide Switch
Cool=(low power)
1=(medium power)
2=(maximum power)
Hairdryer
Type 554.02 - 554.05 - 554.08 - 554.11 - 554.13
Pushbutton:
ON=On/Off (pressure must be maintained to operate the hairdryer)
Slide Switch
1=(low power)
2=(maximum power)
Hairdryer
Type 554.03 - 554.06 - 554.09 - 554.12
Slide Switch
0=(OFF)
1=(low power)
2=(maximum power)
Hairdryer
Mod. 533.04 - 533.06 - 554.01 - 554.04 - 554.07
554.10
Pushbutton=On/Off
(pressure must be maintained to operate the hairdryer)
5
2.
Advertisement
Table of Contents
