PARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACE TANCE CRITIQUE POUR LA SÈCURITÈ DU FONCTIONNEMENT, NE LES REMPLACER QUE PAR DES COMPSANTS SONY DONT THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN LE NUMÈRO DE PIÈCE EST INDIQUÈ...
Due to the higher melting point of Lead Free Solder the soldering iron tip temperature needs to be set to 370 degrees centigrade. This requires soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics. For more information on the use of Lead Free Solder, please refer to http://www.sony-training.com - 3 -...
Page 4
l l a . s l . s l . s l . s l . s l e i l . s l t c i n i l i n i y t i - 4 -...
21 pin connector Pin No Signal Signal level Audio output B Standard level : 0.5V rms (right) Output impedence : Less than 1kohm* Audio input B Standard level : 0.5V rms (right) Output impedence : More than 10kohm* Audio output A Standard level : 0.5V rms (left) Output impedence : Less than 1kohm*...
AE-6BAD/Y SELF DIAGNOSTIC SOFTWARE The identification of errors within the AE-6BAD/Y chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In the event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous flashing LED) and then communicate with each device in turn to establish if a device is faulty.
SECTION 2 DISASSEMBLY 2-1. Rear Cover Removal 2-2. Speaker Connector Disconnection => => => => Remove the rear cover fixing screws indicated and pull the Before completely removing the rear cover disconnect the rear cover backwards away from the set. Take care when speaker connector which is located on the inside of the set.
2-4. Service Position 2-5. G Board Removal Clips To remove the G Board remove the two screws from the To place the chassis in the service position, insert the main middle of the board, release the clips circled and ease the bracket firmly into the T-slot located on the left corner of the board gently away from the support bracket.
2-8. Picture Tube Removal WARNING: BEFORE REMOVING THE ANODE CAP High voltage remains in the CRT even after the power is disconnected. To avoid electric shock, discharge CRT before attempting to remove the anode cap. Short between anode and CRT coated earth ground strap.
SECTION 3 SET-UP ADJUSTMENTS • When complete readjustment is necessary or a new picture tube Carry out the adjustments in the following order : is installed, carry out the following adjustments. 3-1. Beam Landing. • Unless there are specific instructions to the contrary, carry out 3-2.
Fig.3-4 Align both Purity Purity magnets Purity control magnets magnets to the vertical position Align pips on each magnet 3-2. Convergence (1) Screen centre convergence [Static convergence] Input a dot pattern signal from the pattern generator. Normalize the picture setting. [Moving vertically], adjust the V.STAT magnet so that the vertical red, green and blue dots coincide at the centre of the screen.
Page 19
Correction for HMC [Horizontal mis-convergence] and VMC HTIL correction can be performed by adding a THL correction [Vertical mis-convergence] by using the BMC [Hexapole] assembly to the Deflection yoke. magnet. a). HMC correction by BMC [Hexapole] magnet and movement of the electron beam.
Layout of each control 3-3. Focus Adjustment Receive a television broadcast signal. Normalize the picture setting. Purity magnet Adjust the focus control located on the flyback transformer to BMC (Hexaploe) magnet obtain the best focus at the centre of the screen. V STAT convergence magnet Bring only the centre area of the screen into focus, the magenta- Y-splitting axis correction magnet...
SECTION 4 CIRCUIT ADJUSTMENTS 4-1. Electrical Adjustments Service adjustments to this model can be performed using the supplied remote Commander RM-943. Programming the Remote Commander for Operation in Service Mode Press and hold the left Mode Select button until the VCR and DVD LED’s flash. Press 99999.
Page 22
Sub Brightness Adjustment Input a Monoscope pattern. Program the Remote Commander for operation in Service Mode. [ See Page 21 ]. Press ‘AUX/VIDEO’ ‘AUX/VIDEO’ 13 on the Remote Commander. Adjust the ‘Sub-Brightness’ data so that there is barely a difference between the 0 IRE and 10 IRE signal levels. Sub Contrast Adjustment Input a video signal that contains a small 100% white area on a black background.
Sub Colour Adjustment 4-2. TEST MODE 2: Receive a PAL colour bar signal. Test Mode 2 is available by programming the Remote Commander for Connect an oscilloscope to Pin 5 of CN7331 [C Board]. operation in Service Mode [ As shown on Page 21 ] then pressing the Program the Remote Commander for operation in Service Mode.
5-1. BLOCK DIAGRAMS (1) CN3601 IC3600 RIGHT OUT AUDIO/VIDEO SWITCH BUFFER V-OUT-35 V-OUT-3B RIGHT IN V-OUT-15 LAST RF SC3-IN-R Q3656 AV3 IN R LEFT OUT V-OUT-25 AV2 OUT SC2-IN-R AV2 I R LEFT IN CVBS/Y MAIN BUFFER CVBS Y MAIN SC1-IN-R V-OUT-25 V-OUT-2B...
5-1. BLOCK DIAGRAMS (3) IC8700 IC8701 CN8203 CN8700 V DRV+ Q8700 DRIVERS Q8702, Q8703 V DRV- Q8701 TO A BOARD ABL-COMP CN3008 Q8704 DQP-DRV CN8206 Q8508 Q8512 DQP-V-COMP TO VM BOARD CN9401 IC8527 IC8103 COMPARATOR CN2912 HP R HP R J2901 TO A BOARD Q8118, Q8201,...
B-#SSAE6B<...>-A..-29FQ85 10000PF 0.47 0.47 ROTATION COIL TO J BOARD CN3604 0.01 0.01 3.9K AV LINK CONVERTER 3.9K ~ A Board Schematic Diagram [ Audio, Deflection J Interface ] Page 1/3 ~ - 30 -...
Page 31
B-#SSAE6B<...>-A..-29FQ85 COMPONENTS MARKED AS XX ARE NOT FITTED ON THIS MODEL F1101 BTF-EC411 10UH TAB(CONTACT) BA12T 12V REGULATOR KF25BDT 2.5V REGULATOR 150K ~ A Board Schematic Diagram [ Tuner, Regulators ] Page 2/3 ~ - 31 -...
Page 32
4.7K 0.01 B-#SSAE6B<...>-A..-29FQ85 ~ A Board Schematic Diagram [ B Interface ] Page 3/3 ~ - 32 -...
Page 33
~ A Printed Wiring Board Conductor side A ~ - 33 -...
Page 34
~ A Printed Wiring Board Conductor side B ~ - 34 -...
~ F1 Board Schematic Diagram [ Power Switch, Fuse, SIRCS and Stand-By LED ] ~ ~ H1 Board Schematic Diagram [ Front AV Input, Headphone and Control Switches ] ~ TO J BOARD TO A BOARD F1.-29FQ85 CN3600 CN2300 POWER SWITCH, FUSE, SIRCS &...
Page 41
~ G Board Semiconductor Location Table ~ ~ G Printed Wiring Board Conductor side ~ ~ H1 Printed Wiring Board Conductor side ~ Note : Portions of the circuit contained within the marked areas as shown have high voltages present. Use care to prevent electric shock during inspection or repair.
B-#SSAE6B<...>-G..-29FQ85 OVER CURRENT PROTECTION D1NL40-TA2 4.7UH CONTROL IC 4700 SW MOSFET 4.7UH SW MOSFET S1VB40 SWITCH ~ G Board Schematic Diagram [ Power Supply ] ~ - 42 -...
SECTION 6 EXPLODED VIEWS NOTE : Items with no part number and no description are not Items marked “*” are not stocked stocked because they are seldom required for routine since they are seldom required for service. routine service. Some delay should The construction parts of an assembled part are indicated be anticipated when ordering these items.
SECTION 7 ELECTRICAL PARTS LIST PARTS LISTING TABLE OF CONTENTS Page A BOARD COMPLETE Parts List : ....................55 D BOARD COMPLETE Parts List : ....................61 B BOARD COMPLETE Parts List : ....................65 D2 BOARD COMPLETE Parts List : ....................
Page 79
REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK R2647 1-216-853-11 METAL CHIP 470K 5% 1/10W R3658 1-216-837-11 METAL CHIP 1/10W R2648 1-216-821-11 METAL CHIP 1/10W R3659 1-216-821-11 METAL CHIP 1/10W R2649 1-216-837-11 METAL CHIP 1/10W R3660 1-216-841-11 METAL CHIP 1/10W R2650 1-216-837-11 METAL CHIP...
Page 80
*4-095-663-31 CUSHION, CRUSHED HONEYCOMB R9425 1-243-572-21 METAL OXIDE *4-095-957-01 PAPER CUSHION R9426 1-216-839-11 METAL CHIP 1/10W R9427 1-216-839-11 METAL CHIP 1/10W 4-095-508-11 INSTRUCTION MANUAL(KV-29FQ85E) (GERMAN/GREEK/TURKISH) R9429 1-216-821-11 METAL CHIP 1/10W 4-095-508-21 INSTRUCTION MANUAL(KV-29FQ85E) R9430 1-216-809-11 METAL CHIP 1/10W (ENGLISH/GERMAN/FRENCH/ITALIAN) R9431...
Page 81
• User programmable Functional Check through Infrared • Fast and documented Test Mode setting of all Sony TV chassis Additional features such as Adjustments and Troubleshooting are available in chassis-dependent software modules. Please contact your local Sony Service organisation for the latest information.