Advertisement
Quick Links
Download this manual
See also:
User Manual
FOR SERVICE PERSONNEL ONLY
HITACHI SPLIT-UNIT AIR CONDITIONER
INSTALLATION MANUAL
Indoor Unit
Outdoor Unit
RAS-X18CBT
RAC-X18CBT
SAFETY PRECAUTION
Read the safety precautions carefully before operating the unit.
●
The contents of this section are vital to ensure safety. Please pay special attention to the following sign.
●
!
WARNING ........ Incorrect methods of installation may cause death or serious injury.
!
CAUTION ......... Improper installation may result in serious consequence.
Be sure that the unit operates in proper condition after installation. Explain to customer the proper way of
operating the unit as described in the user's guide.
!
Please request your sales agent or qualifi ed technician to install your unit. Water leakage, short circuit or fi re may occur if
●
you do the installation work yourself.
Please observe the instructions stated in the installation manual during the process of installation. Improper installation may
●
cause water leakage, electric shock and fi re.
Make sure that the units are mounted at locations which are able to provide full support to the weight of the units. If not,
●
the units may collapse and impose danger.
Observe the rules and regulations of the electrical installation and the methods described in the installation manual when
●
dealing with the electrical work. Use power cables approved by the authorities of your country.
●
Be sure to use the specifi ed wire for connecting the indoor and outdoor units. Please ensure that the connections are tight
after the conductors of the wire are inserted into the terminals. Improper insertion and loose contact may cause over-heating
and fi re.
●
Please use the specifi ed components for installation work. Otherwise, the units may collapse or water leakage, electric shock
and fi re may occur.
●
Be sure to use the specifi ed piping set for R410A. Otherwise, this may result in broken copper pipes or faults.
●
When installing or removing an air conditioner, do not allow air or moisture to remain in the refrigeration cycle. Otherwise,
pressure in the refrigeration cycle may become abnormally high so that a rupture may be caused.
Be sure to ventilate fully if a refrigerant gas leak while at work. If the refrigerant gas comes into contact with fi re, a poisonous
●
gas may occur.
After completion of installation work, check to make sure that there is no refrigeration gas leakage. If the refrigerant gas
●
leaks into the room, coming into contact with fi re in the fan-driven heater, space heater, etc., a poisonous gas may occur.
Unauthorized modifi cations to the air conditioner may be dangerous. If a breakdown occurs please call a qualifi ed air
●
conditioner technician or electrician. Improper repairs may result in water leakage, electric shock and fi re, etc.
A circuit breaker or fuse (20A time delay) must be installed. Without a circuit breaker or fuse the danger of electric
●
shock exists.
The external switch shall be incorporated to completely disconnect from power supply. It should disconnect all poles, and a
contact separation of at least 3mm must be present.
●
Do not install the unit near a location where there is fl ammable gas. The outdoor unit may catch fi re if
fl ammable gas leaks around it.
Do not install the indoor unit in a machine shop or kitchen where vapor from oil or its mist fl ows to the indoor unit. The oil
●
will deposit on the heat exchanger, thereby reducing the indoor unit performance and may deform and in the worst case,
break the plastic parts of the indoor unit.
●
Please ensure smooth fl ow of water when installing the drain hose.
Piping shall be suitable supported with a maximum spacing of 1m between the supports.
●
1
Installation of Hanger, Wall Penetration and Installation of Protection Pipe
!
CAUTION
The draining of the water container inside the indoor unit can be done from the
●
left. Therefore the hanger must be fi xed horizontally or slightly tilted towards the
side of drain hose. Otherwise, condensed water may overfl ow the water container.
Direct Mounting On The Wall
Please use hidden beams in the wall to hold the hanger.
●
Procedures of Installation and Precautions
Procedures to fi x the hanger.
●
1. Drill holes on wall.
2. Push plug into the holes.
(As shown below)
(As shown below)
●
Procedures to fi x the holder of remote controller.
1. Drill holes on wall.
2. Push plug into the holes.
(As shown below)
(As shown below)
Wall Penetration and Installation of Protection Pipe
Drill a ø 65mm hole on
●
wall which is slightly tilted
towards the outdoor side.
Drill the wall at a small angle.
Cut the protection pipe
●
a c c o r d i n g t o t h e w a l l
thickness.
●
Empty gap in the sleeve of
protection pipe should be
completely sealed to avoid
dripping of rain water into
the room.
<
>
IA811: A
Carefully read through the procedures of proper
●
installation before starting installation work.
●
The sales agent should inform customers regarding
the correct operation of installation.
Tools Needed For Installation Work
+ –
●
Screwdriver
●
Measuring Tape
●
Saw
●
Pipe Cutter
●
Hexagonal Wrench Key (
●
Power Drill (ø 65mm)
●
Vacuum Pump
Wrench
●
Torque Wrench
●
Vacuum Pump Adaptor
●
Flare Tool
●
Gas Leakage Detector
●
Charge Hose
●
Reammer
●
File
WARNING
!
CAUTION
2
Installation of the Indoor Unit
VERTICALLY DOWNWARD PIPING
Preparation
●
Connect connecting cord.
Pull out the pipe, connecting cord and drain
●
hose.
Installation
●
The upper part of the indoor unit is hanged on the hanger.
●
The projection at the lower part of the indoor unit is hooked
onto the hanger.
HORIZONTAL PIPING
Preparation
Change of Drain Hose and Installation Procedures.
Exchange the location of drain hose and drain cap during horizontal piping as shown
●
in fi gure below. Be sure to plug in the drain hose until the insulating material folds
upon itself.
Please use pliers to pull
●
out the drain cap.
3. Fix the hanger on wall
(This is an easier way to
with 4.1 x 32 screw
remove the drain cap).
(As shown in fi gure below)
Remove the cap for
●
drain hose installation
!
CAUTION
Be sure that the wire is not
in contact with any metal
in the wall. Please use
the protection pipe as wire
passing through the hollow
part of the wall so as to
prevent the possibility of
CAUTION
damaged by mouse.
THE CHOICE OF MOUNTING SITE
●
The unit should be mounted at stable, non-vibratory location
which can provide full support to the unit.
●
No nearby heat source and no obstruction near the air outlet is
allowed.
●
The clearance distances from top, right and left are specifi ed in
fi gure below.
●
Knife
●
The location must be convenient for water drainage and pipe
connection with the outdoor unit.
4mm)
●
To avoid interference from noise please place the unit and its
●
Pliers or
remote controller at least 1m from the radio, television and inverter
type fl uorescent lamp.
●
To avoid any error in signal transmission from the remote controller,
●
Manifold Valve
please put the controller far away from high-frequency machines
and high-power wireless systems.
●
The installation height of indoor unit must be 2.3m or more.
Names of Indoor Components
Item
No.
Hanger
1
Screw for Hanger
2
( 4 . 1 x 3 2 )
Holder for Remote
Controller
3
AAA Size Battery
4
Screw for holder of
Remote Controller
5
( 3 . 1 x 1 6 )
Remote Controller
6
Purifying Filter
7
!
Please pull the lower
part of the indoor unit
outwards to check if
the unit is hooked
onto the hanger.
Improper installation
may cause vibration
and noise.
Condensed water
!
may leak out if not
inserted properly.
(Please note the following matters and obtain permission from customer before installation).
!
WARNING
●
The outdoor unit must be mounted at a location which can sup-
port heavy weight. Otherwise, noise and vibration will increase.
!
CAUTION
●
Do not expose the unit under direct sunshine or rain. Besides,
ventilation must be good and clear of obstruction.
●
The air blown out of the unit should not point directly to animals
or plants.
●
The clearances of the unit from top, left, right, front and back
are specifi ed in fi gure below. At least three of the above sides
must be open air.
●
Be sure that the hot air blown out of the unit and noise do not
disturb the neighbourhood.
●
Do not install at a location where there is fl ammable gas, steam,
oil and smoke.
Place the outdoor unit and its connection wire at least 1m away
●
from the antenna or signal line of television, radio or telephone.
This is to avoid noise interference.
●
Do not install outdoor unit facing strong wind direction. It may
damage the fan motor.
Qty
Figure showing the Installation of Indoor and Outdoor Unit.
1
Direction of Piping
6
Be sure to
completely
seal any gap.
1
T h e r e a r e 6 d i r e c t i o n s
allowed, namely, horizontally
perpendicular to the unit,
vertically down from right,
horizontally out from right,
h o r i z o n t a l l y o u t t o l e f t ,
2
horizontally out to right,
vertically down from left.
Don't form the piping downward
at the left of the unit.
2
Dimension of Mounting Stand
of the outdoor unit
(unit : mm)
1
2
INSTALLATION OF REFRIGERATING PIPES AFTER CONNECTION
●
The refrigerating pipes should be adjusted to fi t
into the hole on the wall and then ready for further
connection.
●
The terminals of 2 connected pipes must be covered
with insulator used for terminal connection. Then the
pipes are wrapped with insulation pipe.
●
Connect the connecting cord after removing electrical
cover. (Refer to "CONNECTION OF POWER CORD")
●
After adjustment, fi t the connecting cord and pipes
into the space available under the indoor unit. Use
holder to hold them tight.
CAUTION
●
Holder can be attached at the either of 2 places.
Please select the easier position.
THE CONNECTION OF REFRIGERATING PIPE DURING THE
INSTALLATION OF INDOOR UNIT
Preparation To Install Refrigerating Pipes
●
The refrigerating pipes and connecting cord
arrangement are attached.
●
The end of the refrigerating pipes are at locations
marked with "
" symbol.
Installation
Hang the Indoor unit onto the hanger. Use the temporary
stand at the back of the Indoor unit to push its lower part
15cm forwards. (Shown as right fi gure)
●
Place the drain hose through the hole on the wall.
●
Wrap the refrigerating pipes with insulation pipe after
connecting refrigerating pipe.
●
Connect the connecting cord after removing electrical cover.
(Refer to "Connection of Power Cord")
●
After adjustment, the connecting cord and refrigerating pipes
are placed into the space available under the Indoor unit.
●
The projection of Indoor unit must hook to the hanger.
Heat insulation pipe
Pull this to the front
during the connection
Connecting
cord
of refrigerating pipes
to ease task.
Refrigerating pipe
3
Installation of Drain Hose
You are free to choose the side (left or right) for the installation of drain
!
hose. Please ensure the smooth fl ow of condensed water of the Indoor
CAUTION
unit during installation. (Carelessness may result in water leakage.)
!
WARNING
!
CAUTION
The refrigerant piping should
be insulated with the enclosed
insulation pipe. (If the insulator
is insufficient, please use
commercial products).
●
The difference in height
between the indoor and
outdoor unit should be
kept below 10m.
●
The connecting pipe,
no matter big or small,
should all be insulated
with insulation pipe and
then wrapped with vinyl
tape. (The insulator will
deteriorate if it is not
wrapped with tape).
The connection of insulated
drain hose.
Please use insulated drain
hose for the indoor piping
(commercial product).
!
CAUTION
●
The rubber strap used for
fi xing the insulator should
not be tied with great force.
Otherwise, this will damage
heat insulation and causes
water condensation.
!
CAUTION
●
Please fi x in the plastic core
after fl aring to avoid plastic
chips entering the pipes.
!
CAUTION
Be sure that the
drain hose is not
loosely connected
or bend.
Advertisement
Related Manuals for Hitachi RAS-X18CBT
Summary of Contents for Hitachi RAS-X18CBT
-
Page 1: Installation Manual
No nearby heat source and no obstruction near the air outlet is ● Do not expose the unit under direct sunshine or rain. Besides, HITACHI SPLIT-UNIT AIR CONDITIONER ventilation must be good and clear of obstruction. allowed. Tools Needed For Installation Work ●... - Page 2 Please mount the outdoor unit on stable ground to prevent Preparation of Pipe Removal Of Air From The Pipe And Gas Leakage Inspection ● vibration and increase of noise level. Use a pipe cutter to cut ● Proced res of sing ac P p for Air Re o al the copper pipe.