Page 1 DCM-M1 SERVICE MANUAL US Model Canadian Model Ver 1.3 2000. 08 E Model With SUPPLEMENT-1 (9-927-635-81) With SUPPLEMENT-2 (9-927-635-82) With SUPPLEMENT-3 (9-927-635-83) Model Name Using Similar Mechanism NEW Lens Section Mechanism Type CT-DCMM1-164 Model Name Using Similar Mechanism NEW Section...
Page 2 SONY PARTS WHOSE PART NUMBERS APPEAR AS DE FONCTIONNEMENT. NE REMPLACER CES COM- SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- POSANTS QUE PAR DES PIÈCES SONY DONT LES LISHED BY SONY. NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
Page 3: Table Of Contents
TABLE OF CONTENTS Section Title Page Section Title Page SERVICE NOTE ..........PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS GENERAL 4-1. Frame Schematic Diagram .......... 4-5 Getting Started ..............1-1 4-2. Printed Wiring Boards and Schematic Diagrams ..4-9 Recording – Basics ............... 1-5 VC-216 Printed Wiring Board ........
Page 4: Service Note
SERVICE NOTE • NOTE FOR REPAIR When remove a connector, don’t pull at wire of connector. Be in danger of the snapping of a wire. Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Do not insert the cable insufficiently nor crookedly.
Page 5: General
DCM-M1 SECTION 1 This section is extracted from in- struction manual. (3-866-152-11) GENERAL...
Page 14 1-10...
Page 15 1-11...
Page 16 1-12...
Page 17 1-13...
Page 18 1-14...
Page 19 1-15...
Page 20 1-16...
Page 21 1-17...
Page 22 1-18...
Page 23 1-19...
Page 24 1-20...
Page 25 1-21...
Page 26 1-22...
Page 27 1-23...
Page 28 1-24...
Page 29 1-25...
Page 30 1-26...
Page 31 1-27...
Page 32 1-28...
Page 33 1-29...
Page 34 1-30 E 1-30...
Page 35: Disassembly
DCM-M1 SECTION 2 DISASSEMBLY • This set can be disassembled in the order shown below. DCM-M1 Main Control Switch Unit (Page 2-3) Cabinet (R) Section (Page 2-3) Power Board Zoom Switch Unit Microphone Unit (Page 2-4) (Page 2-3) (Page 2-5)
Page 36 PAPER BOX FOR SCREW We suggest to make a photo copy of this page before removing the set, put cellophane tape (adhesive tape) in each dotted-line frame for each screw. You can replace these screws without any mistakes after this preparation. (If you use OHP sheet or something similar, you can use it repeatedly.) unit: mm...
Page 37: Main Control Switch Unit
Note: Follow the disassembly procedure in the numerical order given. 2-1. MAIN CONTROL SWITCH UNIT 2-3. ZOOM SWITCH UNIT 3 Two screws (S1) (M1.7 × 3) 2 Zoom switch unit 5 Two screws (S3) (M1.7 × 4) 6 Main control switch unit 4 Screw (S2) (M1.7 ×...
Page 38: Power Board
2-4. POWER BOARD 2-6. JACK BOARD 1 Open the jack cover. 3 Flexible board (remote terminal unit) (CN8004) 3 Earth lug 2 Two screws (S7) (M1.7 × 5) 5 Remove the JACK board 1 Connector in the direction of the arrow. 4 Two screws (S8) 5 POWER board 4 Two screws (S8)
Page 39: Remote Terminal Unit
2-7. REMOTE TERMINAL UNIT 2-9. MICROPHONE BLOCK 1 Connector (CN3001) 5 Microphone block 3 Screw (S8) 1 Screw (S8) 2 Remove the remote (M1.7) (M1.7) terminal unit in the direction of the arrow. 2 Flexible board (remocon ray-catcher block unit) 4 Lug (CN8003) 2-8.
Page 40: Main Board
2-10. MAIN BOARD 2-12. HINGE COVER 2 Flexible board 9 Hinge cover (upper control switch unit) (rear) 6 Two screws (S10) (CN8002) (M1.7 × 2.5) 1 Flexible board 3 VF flexible board (VC-216 board) (CN4511) (CN8101) 7 LCD detection sw flexible board (CN8006) qa MAIN board...
Page 41: Lcd Block
2-13. LCD BLOCK 2-15. LCD BOARD 8 Flexible board 4 Boss (fluorescent tube) (CN4307) 7 Flexible board (touch panel) (CN4301) 6 Flexible board 2 Screw (S11) (PS2 × 5) (LCD) qa LCD board (CN4306) 5 Boss 9 Screw (S8) (M1.7) 6 Remove the LCD block in the direction of the arrow.
Page 42: Fluorescent Tube
2-16. FLUORESCENT TUBE 2-18. EVF BLOCK 1 Screw (S3) (M1.7 × 4) 2 EVF block 1 Claw 2 Fluorescent tube 2-17. TOUCH PANEL, LCD MODULE (LCD4301) 1 Two screws (S10) (M1.7 × 2.5) 2 Claw 4 Hinge assembly 3 Claw 5 Claw 6 Touch panel, LCD module (LCD4301)
Page 43: Vf Board
2-19. VF BOARD 2-21. BL BOARD 1 Flexible board (LCX024AK-5) (CN4702) 4 BL board 4 Claw 2 Two claws 2 Claw 7 VF board 6 Two claws 3 Two claws 3 Claw 5 Claw 2-22. UPPER PANEL ASSEMBLY 1 VF/LCD Flexible board (CN4601) 2-20.
Page 44: Mechanism Deck (Mt-Dcmm1-163)
2-23. MECHANISM DECK (MT-DCMM1-163) 2 Two screws (S13) (damper) 5 Two dampers (MD) 6 Damper (MD) 9 Hold the part maked A in the figure trying not to touch either over write head or OP. Pulling the mechanism deck (MT-DCMM1-163) toward you, pull out it to the disc slot side.
Page 45: Stepper Block Assembly (M5811)
2-25. STEPPER BLOCK ASSEMBLY (M5811) 5 Stepper block assembly (M5811) 2 Motor flexible board 3 Screw (S15) (M1.4) 1 Remove solders of motor flexible board. 4 Claw 2-26. HOLDER ASSEMBLY 3 Screw (S16) (M1.4) 4 Holder guide 1 Flexible board (CLV board) 5 Shaft (CN5902) 6 Shaft...
Page 46: Service Position
2-27. SERVICE POSITION Preparation: Refer to previous section “DISASSEMBLY”, and connect as shown in the figure after each part has been removed. AC adaptor MAIN BOARD, CLV BOARD (AC-VQ800) AC in Zoom switch unit Battry case assembly Main control switch unit MAIN board Lens block CLV board...
Page 47 MEMO 2-13...
Page 48: Circuit Boards Location
2-28. CIRCUIT BOARDS LOCATION BL board (EVF BACK LIGHT) VF board (EVF) POWER board (DC/DC CONVERTER) MAIN board AUDIO/VIDEO DATA CONTROL, MPEG ENCODER/DECODER, RF AMP/DRIVE, DIGITAL SIGNAL PROCESSOR, SYSTEM CONTROL, VIDEO, AUDIO, SWITCHING REGULATOR 2-14...
Page 49 ETHER board (ETHER INTERFACE) JACK board (AV IN/OUT) LCD board (LCD) VC-216 board LENS MOTOR DRIVE, CCD IMAGER, CAMERA SIGNAL PROCESS REC board OVER WRITE HEAD DRIVE CLV board (MD MOTOR DRIVE) 2-15...
Page 50: Flexible Boards Location
2-29. FLEXIBLE BOARDS LOCATION 3 VF/LCD flexible board Upper control switch unit Remote terminal unit 1 Translation flexible board Remocon ray-catcher block unit Fluorescent tube LCD module (LCD4701) Lens device Zoom switch unit 4 LCD detection sw flexible board LCD module (LCD4301) Touch panel 2-16...
Page 51 5 Motor flexible board VF flexible board 2 Translation flexible Over write head (HR5901) (jack) board Spindle motor (M5821) OP block unit: mm 2 Translation flexible (jack) board 3 VF/LCD flexible board 1 Translation flexible board 4 LCD detection sw flexible board 5 Motor flexible board 2-17 E 2-17...
Page 52: Block Diagrams
DCM-M1 SECTION 3 BLOCK DIAGRAMS 3-1. OVERALL BLOCK DIAGRAM ZOOM LENS UNIT VC-216 BOARD CLV BOARD REC BOARD MAIN BOARD (SEE PAGE 4-29 to 59) IRIS METER ZOOM LENS (SEE PAGE 4-13, 17) IC5501 (1/2) (SEE PAGE 4-79) HR5901 OVER WRITE HEAD...
Page 53: Camera Signal Process Block Diagram
DCM-M1 3-2. CAMERA SIGNAL PROCESS BLOCK DIAGRAM VC-216 BOARD (1/2) (SEE PAGE 4-13, 17) CAMERA Y/C PROCESS IC105 (1/2) 1 Vp-p CDS, AGC, A/D CONVERTER CN101 (1/2) CLPOB 20 TO A/V DATA CONTROL, REC/PB CLPOB IC102 VIDEO OUT YO 0...
Page 54: Camera Control Block Diagram
DCM-M1 3-3. CAMERA CONTROL BLOCK DIAGRAM VC-216 BOARD (2/2) (SEE PAGE 4-13 to 17) SENSOR AMP 1.22 Vp-p SE001 IC002 20 MHz CAMERA CONTROL REC/PB Vref 1 IC106 XTAL OUT 1 YAW AD SENSOR LIA 1 X102 20MHz EXTAL CRST...
Page 55: A/V Data Control, Video Out Block Diagram
DCM-M1 3-4. A/V DATA CONTROL, VIDEO OUT BLOCK DIAGRAM MAIN BOARD (1/7) JACK BOARD (1/4) AUDIO & VIDEO DATA CONTROL (SEE PAGE 4-29, 48, 53, 59) (SEE PAGE 4-119) IC8101 Y VIDEO SIGNAL AMP Y VIDEO SIGNAL AMP IC4004 IC4003...
Page 56: Mpeg Encode Block Diagram
DCM-M1 3-5. MPEG ENCODE BLOCK DIAGRAM MAIN BOARD (2/7) (SEE PAGE 4-33, 59) 64M SDRAM IC8602 – • • • • • • • • • • • • • • • • • 17 18 19 68 • •...
Page 57: Md Signal Process Block Diagram
DCM-M1 3-6. MD SIGNAL PROCESS BLOCK DIAGRAM MAIN BOARD (3/7) 1M FAST SRAM IC5501 (SEE PAGE 4-39, 43) SRAM CS – • – • • • • • 28 12 – • • • MD2 DIGITAL SIGNAL PROCESSOR IC5403(1/2) –...
Page 58: Md Servo Block Diagram
DCM-M1 3-7. MD SERVO BLOCK DIAGRAM MAIN BOARD (4/7) OPTICAL PIC-UP BLOCK (SEE PAGE 4-39, 43) DIGITAL SERVO SIGNAL PROCESSOR FOCUS/TRACKING COIL DRIVE, (2/2) IC5301 (2/2) SLED MOTOR DRIVE TO MD SIGNAL PROCESS IC5602 (SEE PAGE 3-11) CN5001 2-AXIS DEVICE...
Page 59: System Control Block Diagram
DCM-M1 3-8. SYSTEM CONTROL BLOCK DIAGRAM MAIN BOARD (5/7) (SEE PAGE 4-48, 59) CN8101 CN4312 IC4007 (1/2) (2/3) DATA_TO_HI LCD_SI XHI_SCK IC4007 TO CAMERA CONTROL DATA_FROM_HI LCD_SCK TO LCD (SEE PAGE 3-6) (SEE PAGE 3-19) IC4008 LCD_SO SYSTEM CONTROL IC4008...
Page 60: Audio Block Diagram
DCM-M1 3-9. AUDIO BLOCK DIAGRAM ETHER BOARD MAIN BOARD (6/7) (1/2) (SEE PAGE 4-48, 56) (SEE PAGE 4-109) JACK BOARD (3/4) HP/LINE AMP ETHER ADAPTER (SEE PAGE 4-119 ) IC3007 (1/2) CN8802 CN8801 (1/2) (1/2) CN3002 (3/4) CN3003 (3/4) CN8007 (3/3)
Page 61: Lcd Block Diagram
DCM-M1 3-10. LCD BLOCK DIAGRAM LCD BOARD (1/2) 4 Vp-p (SEE PAGE 4-106) REC/PB LCD DRIVER LCD UNIT IC4302 LCD4301 4 Vp-p 560 mVp-p REC/PB REC/PB CN4303 CN4306 PANEL_Y G_OUT BUFFER PICTURE Q4303, 4304 TO A/V DATA CONTROL, VIDEO OUT...
Page 62: Evf Block Diagram
DCM-M1 3-11. EVF BLOCK DIAGRAM VF BOARD (SEE PAGE 4-87) 208 mVp-p 8 Vp-p 8 Vp-p LCD DRIVER 500 mVp-p REC/PB REC/PB IC4501 REC/PB CN4501 CN4601 CN4701 CN4702 G OUT EVF_Y BUFFER PICTURE Q4502, 4503 TO A/V DATA CONTROL, VIDEO OUT...
Page 63: Mode Control Block Diagram
DCM-M1 3-12. MODE CONTROL BLOCK DIAGRAM LCD BOARD (2/2) MAIN BOARD (7/7) (SEE PAGE 4-106) SYSTEM CONTROL (SEE PAGE 4-29, 48, 56, 59) SH3.1V IC8001 CN4302 (2/2) CN4312 (2/2) TP Y1 SWITCH TP Y1 118 UPPER CONTROL SW SUB ASSY...
Page 64: Ether Interface Block Diagram
DCM-M1 3-13. ETHER INTERFACE BLOCK DIAGRAM LEVEL SHIFT ETHER BOARD (2/2) IC8801 (SEE PAGE 4-109) D0 – D7 SD0 – SD7 ETHER INTERFACE IC8806 CN8801 (2/2) ETHER ADAPTER PULSE TRANSFORMER LEVEL SHIFT (2/2) IC8807 IC8802 CN8802 • • (2/2) •...
Page 65: Power 1 Block Diagram
DCM-M1 3-14. POWER 1 BLOCK DIAGRAM BATTERY TERMINAL POWER BOARD (SEE PAGE 4-130) CN9002 CN9001 BATT_SIG BATT_SIG BATT_SIG AC_DETECT AC_DETECT TO MAIN BOARD AC_DETECT_SW DD_CTL U_GND CN9101 (2/2) LITIUM_BATT_ – (SEE PAGE 3-30) (AC_IN_ –) F9001 L9001 LITIUM BATT_+ LITIUM_BATT_+...
Page 66: Power 2 Block Diagram
DCM-M1 3-15. POWER 2 BLOCK DIAGRAM UPPER CONTROL ETHER BOARD (SEE PAGE 4-109) CN8002 CN8301 MAIN BOARD SW SUB ASSY D2.85V D2.85V (SEE PAGE 4-29 to 59) (SEE PAGE 4-65) CN8007 CN8801 D3.1V IC8801 IC8804 TO POWER BOARD IC8802 IC8805...
Page 67: Power 3 Block Diagram
DCM-M1 3-16. POWER 3 BLOCK DIAGRAM VC-216 BOARD VF BOARD BL BOARD BACK LIGHT (SEE PAGE 4-13, 17) (SEE PAGE 4-87) (SEE PAGE 4-97) ND4701 CN101 CN4501 CN4601 CN4701 TO MAIN BOARD TO MAIN BOARD 4.95V (CAMERA) EVF 4.95V EVF BL 4.95V...
Page 68: Printed Wiring Boards And Schematic Diagrams
DCM-M1 DCM-M1 SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) (For schematic diagrams) (For printed wiring boards) (Measuring conditions voltage and waveform) •...
Page 69: Frame Schematic Diagram
DCM-M1 4-1. FRAME SCHEMATIC DIAGRAM FRAME...
Page 70 DCM-M1 4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS • For Printed Wiring Board. VC-216 (LENS MOTOR DRIVE, CCD IMAGER, CAMERA SIGNAL PROCESS) PRINTED WIRING BOARD • There are few cases that the part isn't mounted in this model – Ref. No.: VC-216 board; 20,000 series –...
Page 71: Lens Motor Drive, Ccd Imager) Schematic Diagram
DCM-M1 VC-216 (LENS MOTOR DRIVE, CCD IMAGER) SCHEMATIC DIAGRAM • See page 4-9 for VC-216 printed wiring board. • See page 4-133 for waveforms. 4-13 LENS MOTOR DRIVE, CCD IMAGER VC-216 (1/3) VC-216 (2/3) 4-14 4-15 4-16...
Page 72: Camera Signal Process) Schematic Diagram
VC-216 (CAMERA SIGNAL PROCESS) SCHEMATIC DIAGRAM • See page 4-9 for VC-216 printed wiring board. • See page 4-133 for waveforms. DCM-M1 DCM-M1 CAMERA SIGNAL PROCESS VC-216 (3/3) 4-17 4-18 4-19...
Page 73 DCM-M1 MAIN (AUDIO/VIDEO DATA CONTROL, MPEG ENCODER/DECODER, RF AMP/DRIVE, DIGITAL SIGNAL PROCESSOR, MAIN BOARD (SIDE A) SYSTEM CONTROL, VIDEO, AUDIO, SWITCHING REGULATOR) PRINTED WIRING BOARD • For Printed Wiring Board. – Ref. No.: MAIN board; 10,000 series – R9130 R9904...
Page 74 DCM-M1 DCM-M1 MAIN BOARD (SIDE B) C8046 C8047 TP9102 TP9103 TP5011 TP5018 TP9101 IC8007 IC8006 TP9108 MAIN BOARD (SIDE B) TP9109 TP5013 TP3002 IC8020 Q8008 TP9104 R8061 TP5012 C3048 C8034 C9109 Q5009 R8004 R8519 TP9107 TP9114 IC8013 C3052 C8036 C9110...
Page 75: Main (Audio/Video Data Control) Schematic Diagram
MAIN (AUDIO/VIDEO DATA CONTROL) SCHEMATIC DIAGRAM • See page 4-21 for MAIN printed wiring board. • See page 4-133 for waveforms. DCM-M1 4-29 AUDIO/VIDEO DATA CONTROL MAIN (1/8) 4-30 4-31 4-32...
Page 76: Main (Mpeg Encoder/Decoder) Schematic Diagram
DCM-M1 MAIN (MPEG ENCODER/DECODER) SCHEMATIC DIAGRAM • See page 4-21 for MAIN printed wiring board. • See page 4-133 for waveforms. 4-37 MPEG ENCODER/DECODER MAIN (2/8) 4-33 4-34 4-35 4-36...
Page 77: Main (Rf Amp/Drive) Schematic Diagram
DCM-M1 DCM-M1 MAIN (RF AMP/DRIVE) SCHEMATIC DIAGRAM • See page 4-21 for MAIN printed wiring board. • See page 4-134 for waveforms. RF AMP/DRIVE MAIN (3/8) 4-39 4-41 4-40 4-42...
Page 78: Main (Digital Signal Processor) Schematic Diagram
MAIN (DIGITAL SIGNAL PROCESSOR) SCHEMATIC DIAGRAM • See page 4-21 for MAIN printed wiring board. • See page 4-134 for waveforms. DCM-M1 DCM-M1 4-46 DIGITAL SIGNAL PROCESSOR MAIN (4/8) 4-43 4-44 4-45...
Page 79: Main (System Control) Schematic Diagram
DCM-M1 MAIN (SYSTEM CONTROL) SCHEMATIC DIAGRAM • See page 4-21 for MAIN printed wiring board. • See page 4-133 for waveforms. 4-48 SYSTEM CONTROL MAIN (5/8) 4-51 4-49 4-50 4-52...
Page 80: Main (Video) Schematic Diagram
DCM-M1 MAIN (VIDEO) SCHEMATIC DIAGRAM • See page 4-21 for MAIN printed wiring board. • See pages 4-133, 134 for waveforms. VIDEO MAIN (6/8) 4-53 4-54 4-55...
Page 81: Main (Audio) Schematic Diagram
DCM-M1 MAIN (AUDIO) SCHEMATIC DIAGRAM • See page 4-21 for MAIN printed wiring board. • See page 4-134 for waveforms. AUDIO MAIN (7/8) 4-56 4-57 4-58...
Page 82: Main (Switching Regulator) Schematic Diagram
DCM-M1 MAIN (SWITCHING REGULATOR) SCHEMATIC DIAGRAM • See page 4-21 for MAIN printed wiring board. • See page 4-133 for waveforms. SWITCHING REGULATOR MAIN (8/8) 4-59 4-60 4-61...
Page 83: Main Control Switch Unit, Zoom Switch Unit Schematic Diagram
DCM-M1 MAIN CONTROL SWITCH UNIT, ZOOM SWITCH UNIT SCHEMATIC DIAGRAM 4-62 MAIN CONTROL SWITCH UNIT, ZOOM SWITCH UNIT 4-63 4-64...
Page 84: Upper Control Sw Sub Assy, Remocon Ray-Catcher Block Unit, Lcd Detection Sw Flexible Board Schematic Diagram
DCM-M1 UPPER CONTROL SW SUB ASSY, REMOCON RAY-CATCHER BLOCK UNIT, LCD DETECTION SW FLEXIBLE BOARD SCHEMATIC DIAGRAM 4-67 UPPER CONTROL SW SUB ASSY, REMOCON RAY-CATCHER 4-65 4-66 BLOCK UNIT, LCD DETECTION SW FLEXIBLE BOARD...
Page 85 DCM-M1 CLV (MD MOTOR DRIVE) PRINTED WIRING BOARD – Ref. No.: CLV board; 20,000 series – CLV BOARD (SIDE A) C5807 C-11 R5802 C-11 C5808 C-11 R5803 C-11 C5811 R5806 B-10 C5813 R5807 B-10 C5814 R5809 C-10 C5815 R5810 C-10...
Page 86 DCM-M1 • For Printed Wiring Board. • There are few cases that the part isn't mounted in this model is printed on this diagram. • Chip transistor CLV BOARD (SIDE B) C5804 A-10 C5805 C5806 B-10 C5809 C5810 C-10 C5812...
Page 87 DCM-M1 CLV (MD MOTOR DRIVE) SCHEMATIC DIAGRAM • See page 4-68 for CLV printed wiring board. • See page 4-134 for waveforms. MD MOTOR DRIVE 4-75 4-76 4-77 4-78...
Page 88 DCM-M1 • For Printed Wiring Board. REC (OVER WRITE HEAD DRIVE) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM • There are few cases that the part isn't mounted in this model – Ref. No.: REC board; 20,000 series – is printed on this diagram.
Page 89 DCM-M1 VF (EVF) PRINTED WIRING BOARD VF BOARD (SIDE B) – Ref. No.: VF board; 20,000 series – C4501 • For Printed Wiring Board. C4509 • There are few cases that the part isn't mounted in this model C4515 C4525 VF BOARD (SIDE A) is printed on this diagram.
Page 90 DCM-M1 VF (EVF LCD DRIVE, EVF TIMING GENERATOR) SCHEMATIC DIAGRAM • See pages 4-133, 134, 135 for waveforms. 4-91 EVF LCD DRIVE, EVF TIMING GENERATOR 4-87 4-88 4-89 4-90...
Page 91 DCM-M1 DCM-M1 BL (EVF BACK LIGHT) PRINTED WIRING BOARD – Ref. No.: BL board; 20,000 series – • For Printed Wiring Board. • There are few cases that the part isn't mounted in this model is printed on this diagram.
Page 92 DCM-M1 BL (EVF BACK LIGHT DRIVE, EVF BACK LIGHT) SCHEMATIC DIAGRAM Note: Note: Les composants identifiés par The components identi- une marque 0 sont critiques fied by mark 0 or dotted line with mark 0 are criti- pour la sécurité.
Page 93 DCM-M1 LCD (LCD) PRINTED WIRING BOARD • For Printed Wiring Board. – Ref. No.: LCD board; 20,000 series – • There are few cases that the part isn't mounted in this model is printed on this diagram. • Chip transistor...
Page 94: Lcd Schematic Diagram
LCD (LCD) SCHEMATIC DIAGRAM • See page 4-135 for waveforms. DCM-M1 LCD BOARD (SIDE B) C4301 FB4301 R4337 C4302 D-10 R4338 C4303 D-10 IC4301 R4339 C4304 G-10 IC4302 R4340 C4305 IC4303 R4343 C4306 IC4304 R4344 C4307 R4345 C4308 L4301 E-10...
Page 95 DCM-M1 ETHER (ETHER INTERFACE) PRINTED WIRING BOARD – Ref. No.: ETHER board; 20,000 series – • For Printed Wiring Board. • There are few cases that the part isn't mounted in this model is printed on this diagram. • Chip transistor...
Page 96 DCM-M1 ETHER INTERFACE ETHER 4-113 4-114 4-115...
Page 97 DCM-M1 ETHER (ETHER INTERFACE) SCHEMATIC DIAGRAM • See page 4-109 for printed wiring board. • See page 4-135 for waveforms. ETHER INTERFACE ETHER 4-116 4-117 4-118...
Page 98 DCM-M1 JACK (AV IN/OUT) SCHEMATIC DIAGRAM • See page 4-121 for printed wiring board. AV IN/OUT JACK 4-119 4-120...
Page 99 DCM-M1 JACK (AV IN/OUT) PRINTED WIRING BOARD – Ref. No.: JACK board; 20,000 series – AV IN/OUT JACK 4-121 4-122...
Page 100 DCM-M1 • For Printed Wiring Board. • There are few cases that the part isn't mounted in this model is printed on this diagram. ETHER board (ETHER INTERFACE) JACK board (AV IN/OUT) LCD board (LCD) AV IN/OUT JACK 4-123 4-124...
Page 101: Power Printed Wiring Board
DCM-M1 POWER (DC/DC CONVERTER) PRINTED WIRING BOARD – Ref. No.: POWER board; 20,000 series – POWER BOARD (SIDE A) C9001 A-10 C9002 A-10 C9003 A-10 C9004 C9009 C9011 C9015 C9052 C9055 C9057 C9061 C9063 C9064 C9065 C9068 C9076 C9080 CN9001...
Page 102 DCM-M1 • For Printed Wiring Board. • There are few cases that the part isn't mounted in this model is printed on this diagram. • Chip transistor BL board (EVF BACK LIGHT) VF board (EVF) POWER board (DC/DC CONVERTER) MAIN board...
Page 103 DCM-M1 POWER (DC/DC CONVERTER) SCHEMATIC DIAGRAM • See page 4-125 for printed wiring board. • See page 4-135 for waveforms. Note: Note: The components identi- Les composants identifiés par fied by mark 0 or dotted une marque 0 sont critiques line with mark 0 are criti- pour la sécurité.
Page 104: Waveforms
DCM-M1 4-3. WAVEFORMS 2.88 Vp-p 360 mVp-p 7 Vp-p REC/PB REC/PB REC/PB 2.96 Vp-p 1.12 Vp-p 7 Vp-p REC/PB REC/PB REC/PB Approx. 1 Vp-p 3.1 Vp-p 3.4 Vp-p 13.5 MHz REC/PB REC/PB REC/PB 3.28 Vp-p 3.6 Vp-p 1.22 Vp-p 18 MHz...
Page 105 DCM-M1 Approx. 1.38 Vp-p 680 mVp-p : MD1 980 mVp-p Approx. 1.68 Vp-p Approx.23.6 ms: MD1 Approx.14.8 ms: MD2 : MD2 22.5792 MHz REC/PB REC/PB REC/PB Approx. 560 mVp-p 368 mVp-p : MD1 3.4 Vp-p Approx. Approx.23.6 ms: MD1 780 mVp-p Approx.14.8 ms: MD2...
Page 106 DCM-M1 2.16 Vp-p 1.28 Vp-p 11 MHz 20 MHz REC/PB REC/PB 560 mVp-p 800 mVp-p 470 kHz REC/PB REC/PB 220mVp-p 5.52 Vp-p 470 kHz REC/PB REC/PB 236 mVp-p 940 mVp-p 470 kHz REC/PB REC/PB 4 Vp-p 840 mVp-p 470 kHz...
Page 107: Exploded Views
DCM-M1 SECTION 5 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they • Items marked “*” are not stocked since they The components identified by mark 0 or dotted line with mark may have some difference from the original are seldom required for routine service.
Page 108: Cabinet (R) Section
5-2. CABINET (R) SECTION not supplied not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-218-461-01 SCREW (M1.7) 3-043-016-01 RUBBER, GRIP A-3321-881-A POWER BOARD, COMPLETE 1-418-202-21 SWITCH UNIT, ZOOM * 53 4-216-028-01 CASE (REAR), SHIELD X-3378-880-1 CABINET (R) SUB ASSY 3-043-103-01 CUSHION (SHIELD) 4-216-052-01 BLIND (EVF), ADJUSTMENT...
Page 109: Microphone Block Section
5-3. MICROPHONE BLOCK SECTION not supplied cabinet (L) section LCD block section Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-216-044-01 COVER (FRONT), HINGE 4-220-639-01 ABSORBENT (GEL), ACOUSTIC 4-223-676-15 SCREW (1.7), MI (M1.7X3) 4-216-019-01 COVER, BASE * 103 4-220-721-01 MATERIAL, ACOUSTIC ISOLATION (S) 3-043-171-01 SHEET (MICROPHONE)
Page 110: Cabinet (L) Section
5-4. CABINET (L) SECTION EVF block section CT-DCMM1-164 MT-DCMM1-163 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-3378-420-1 PANEL ASSY, UPPER 3-837-971-01 CUSHION 4-218-229-19 SCREW (1.4), MI (M1.4X2) 4-215-989-01 CUSHION (MD) 3-320-382-11 FOOT, RUBBER 4-218-461-01 SCREW (M1.7) 4-218-458-01 DAMPER (MD) 4-220-349-01 CUSHION (CAMERA) 4-223-676-15 SCREW (1.7), MI (M1.7X3)
Page 111: Lcd Block Section
5-5. LCD BLOCK SECTION LCD4301 The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité. Replace only with part num- Ne les remplacer que par une pièce ber specified.
Page 112: Evf Block Section
5-6. EVF BLOCK SECTION LCD4701 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-672-356-11 VF/LCD FLEXIBLE BOARD 4-216-039-01 CUP, EYE A-3321-877-A BL BORAD, COMPLETE 4-218-460-01 ARM, VISIBILITY ADJUSTMENT 3-989-416-01 CUSHION (458), LCD 4-216-040-01 CABINET (LOWER), EVF 3-988-563-01 ILLUMINATOR (458), BL 3-713-791-01 SCREW (M1.7X5), TAPPING, P2 3-960-302-11 CUSHION (1), LCD...
Page 113: Lens Block Section (Ct-Dcmm1-164)
5-7. LENS BLOCK SECTION (CT-DCMM1-164) supplied not supplied (IC001) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-3250-920-A CT-DCMM1-164 3-961-192-01 RUBBER (FH), SEAL 3-713-791-01 SCREW (M1.7X4), TAPPING, P2 * 308 4-215-974-01 BRACKET, LENS BLOCK * 303 4-215-973-01 BRACKET, LENS FRAME 4-215-989-21 CUSHION (MD) 8-848-732-01 DEVICE, LENS (LSV-620B)
Page 114: Mechanism Deck Section-1 (Mt-Dcmm1-163)
5-8. MECHANISM DECK SECTION-1 (MT-DCMM1-163) M5811 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-349-825-41 SCREW 4-217-948-01 GEAR (WORM WHEEL) A-3321-863-A REC BOARD, COMPLETE X-4951-231-1 HOLDER (STEPPER) ASSY X-4951-230-1 HOLDER ASSY 3-338-645-31 WASHER (0.8-2.5) 4-217-955-01 SPRING (POWER TENSION), TENSION 4-963-883-01 SCREW (M1.4), PRECISION PAN 4-963-883-41 SCREW (M1.4), PRECISION PAN 4-217-958-01 SHEET, ADHESIVE...
Page 115: Mechanism Deck Section-2 (Mt-Dcmm1-163)
5-9. MECHANISM DECK SECTION-2 (MT-DCMM1-163) not supplied (HR5901) supplied not supplied (M5801) not supplied (M5821) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-4952-432-1 SERVICE ASSY, OP 3-704-246-01 SCREW (P 1.4X1.6) 4-963-883-21 SCREW (M1.4), PRECISION PAN 4-217-941-01 BRACKET (LEAD SCREW) X-4951-229-1 CHASSIS ASSY * 415...
Page 116: Electrical Parts List
DCM-M1 SECTION 6 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • Items marked “*” are not stocked since they The components identified by mark 0 or dotted line with mark parts list may be different from the parts speci- are seldom required for routine service.
Page 117 ETHER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R5832 1-218-965-11 RES, CHIP 1/16W IC5806 8-759-082-55 IC TC7W00FU R5833 1-218-965-11 RES, CHIP 1/16W IC5807 8-759-572-28 IC NJU7016R R5834 1-218-965-11 RES, CHIP 1/16W IC5808 8-759-082-55 IC TC7W00FU R5851 1-218-967-11 RES, CHIP 1/16W...
Page 118 ETHER JACK Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < COIL > FB2101 1-469-637-21 FERRITE FB2102 1-469-637-21 FERRITE L8801 1-414-753-91 INDUCTOR 4.7uH FB2103 1-469-637-21 FERRITE < TRANSISTOR > FB3001 1-469-637-21 FERRITE FB3002 1-469-637-21 FERRITE Q8801 8-729-047-36 TRANSISTOR CPH3303-TL FB3003 1-469-637-21 FERRITE...
Page 119 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C4327 1-117-919-11 TANTALUM CHIP 10uF 6.3V C4328 1-164-004-11 CERAMIC CHIP 0.1uF Q4306 8-729-037-53 TRANSISTOR 2SB1462J-QR (TX).SO C4329 1-125-777-11 CERAMIC CHIP 0.1uF Q4307 8-729-037-53 TRANSISTOR 2SB1462J-QR (TX).SO C4330 1-110-501-11 CERAMIC CHIP 0.33uF Q4308 8-729-037-53 TRANSISTOR...
Page 120 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R4371 1-218-975-11 RES, CHIP 1/16W C1020 1-107-686-11 TANTALUM CHIP 4.7uF R4372 1-218-969-11 RES, CHIP 1/16W C1021 1-125-891-11 CERAMIC CHIP 0.47uF R4373 1-218-973-11 RES, CHIP 1/16W C1022 1-164-939-11 CERAMIC CHIP 0.0022uF 10% R4374 1-218-961-11 RES, CHIP...
Page 121 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C5017 1-115-467-11 CERAMIC CHIP 0.22uF C3042 1-107-820-11 CERAMIC CHIP 0.1uF C5018 1-164-942-11 CERAMIC CHIP 0.0068uF 10% C3043 1-107-820-11 CERAMIC CHIP 0.1uF C5019 1-119-923-81 CERAMIC CHIP 0.047uF C3044 1-117-919-11 TANTALUM CHIP 10uF 6.3V C3045...
Page 122 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C8008 1-107-820-11 CERAMIC CHIP 0.1uF C5305 1-107-820-11 CERAMIC CHIP 0.1uF C8009 1-107-820-11 CERAMIC CHIP 0.1uF C5306 1-125-777-11 CERAMIC CHIP 0.1uF C8010 1-107-820-11 CERAMIC CHIP 0.1uF C5307 1-164-847-11 CERAMIC CHIP 0.5PF C5308 1-164-677-11 CERAMIC CHIP...
Page 123 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C8608 1-107-820-11 CERAMIC CHIP 0.1uF C8071 1-164-937-11 CERAMIC CHIP 0.001uF C8609 1-164-937-11 CERAMIC CHIP 0.001uF C8072 1-107-820-11 CERAMIC CHIP 0.1uF C8610 1-107-820-11 CERAMIC CHIP 0.1uF C8073 1-119-750-11 TANTALUM CHIP 22uF 6.3V C8074 1-104-851-11 TANTALUM CHIP 10uF...
Page 124 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark FB8019 1-469-638-21 FERRITE C9127 1-117-919-11 TANTALUM CHIP 10uF 6.3V FB8020 1-469-638-21 FERRITE C9128 1-107-820-11 CERAMIC CHIP 0.1uF FB8021 1-469-637-21 FERRITE C9129 1-107-820-11 CERAMIC CHIP 0.1uF FB8022 1-469-637-21 FERRITE C9130 1-107-820-11 CERAMIC CHIP 0.1uF...
Page 125 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark IC5501 8-759-572-37 IC KM68V1002AT-12 L5601 1-414-407-41 INDUCTOR 330uH IC5601 8-759-482-07 IC MPC17A28SVMEL L5602 1-412-056-11 INDUCTOR 4.7uH IC5602 8-759-460-34 IC MPC17A36VMEL L5603 1-412-056-11 INDUCTOR 4.7uH L5604 1-412-056-11 INDUCTOR 4.7uH IC5603 8-759-578-53 IC XC6365D103MR IC8001 8-759-572-52 IC HD6417709BT80A...
Page 126 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark Q8002 8-729-043-94 TRANSISTOR CPH3106-PM-TL R1028 1-218-975-11 RES, CHIP 1/16W Q8003 8-729-044-20 TRANSISTOR SI6463DQ-T1 R1029 1-218-973-11 RES, CHIP 1/16W R1030 1-208-675-11 METAL CHIP 0.5% 1/16W Q8004 8-729-044-20 TRANSISTOR SI6463DQ-T1 R1032 1-218-955-11 RES, CHIP...
Page 127 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R4010 1-218-957-11 RES, CHIP 2.2K 1/16W R5046 1-218-985-11 RES, CHIP 470K 1/16W R4011 1-208-675-11 METAL CHIP 0.5% 1/16W R5047 1-218-965-11 RES, CHIP 1/16W R5048 1-218-965-11 RES, CHIP 1/16W R4012 1-218-941-11 METAL CHIP...
Page 128 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R5318 1-218-990-11 SHORT R8023 1-218-953-11 RES, CHIP 1/16W R5401 1-218-965-11 RES, CHIP 1/16W R8024 1-218-985-11 RES, CHIP 470K 1/16W R8025 1-218-953-11 RES, CHIP 1/16W R5402 1-218-965-11 RES, CHIP 1/16W R8026 1-218-985-11 RES, CHIP...
Page 129 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R8084 1-218-990-11 SHORT R8514 1-218-977-11 RES, CHIP 100K 1/16W R8085 1-218-983-11 RES, CHIP 330K 1/16W R8515 1-218-977-11 RES, CHIP 100K 1/16W R8516 1-218-977-11 RES, CHIP 100K 1/16W R8086 1-218-983-11 RES, CHIP 330K...
Page 130 MAIN POWER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R9113 1-218-989-11 RES, CHIP 1/16W X5403 1-781-247-21 VIBRATOR, CRYSTAL (70.54MHz) R9114 1-218-989-11 RES, CHIP 1/16W X8001 1-767-994-41 VIBRATOR, CRYSTAL (32.768kHz) X8002 1-767-994-22 VIBRATOR, CRYSTAL (32.768kHz) R9116 1-218-973-11 RES, CHIP 1/16W R9117...
Page 131 POWER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C9050 1-104-851-11 TANTALUM CHIP 10uF < IC > C9051 1-104-852-11 TANTALUM CHIP 22uF IC9001 8-759-596-54 IC SN104241PM-TEB C9052 1-164-937-11 CERAMIC CHIP 0.001uF IC9002 8-759-252-41 IC TK11900MTL C9053 1-115-339-11 CERAMIC CHIP 0.1uF C9055...
Page 132 POWER VC-216 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R9025 1-208-691-11 METAL CHIP 2.2K 0.5% 1/16W < DIODE > R9029 1-208-703-11 METAL CHIP 6.8K 0.5% 1/16W D5901 8-719-073-16 DIODE SBE802-TL R9031 1-218-965-11 RES, CHIP 1/16W D5902 8-719-073-16 DIODE SBE802-TL R9032...
Page 133 VC-216 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C112 1-107-826-91 CERAMIC CHIP 0.1uF < DIODE > C113 1-107-826-91 CERAMIC CHIP 0.1uF D101 8-713-103-84 DIODE 1T379-01-T8A C114 1-164-943-11 CERAMIC CHIP 0.01uF D201 8-719-056-23 DIODE MA2S111- (K8).SO C115 1-165-176-11 CERAMIC CHIP 0.047uF...
Page 134 VC-216 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R102 1-469-537-21 FILTER R224 1-218-973-11 RES, CHIP 1/16W R103 1-218-933-11 RES, CHIP 1/16W R225 1-216-864-11 METAL CHIP 1/16W R104 1-218-977-11 RES, CHIP 100K 1/16W R226 1-216-864-11 METAL CHIP 1/16W R105 1-218-945-11 RES, CHIP...
Page 135 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R4525 1-218-975-11 RES, CHIP 1/16W C4618 1-164-943-11 CERAMIC CHIP 0.01uF C4619 1-135-259-11 TANTALUM CHIP 10uF 6.3V R4526 1-218-971-11 RES, CHIP 1/16W C4620 1-164-874-11 CERAMIC CHIP 100PF R4527 1-218-985-11 RES, CHIP 470K 1/16W C4621...
Page 136 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R4623 1-218-983-11 RES, CHIP 330K 1/16W ACCESSORIES & PACKING MATERIALS R4624 1-218-971-11 RES, CHIP 1/16W ******************************* R4626 1-218-969-11 RES, CHIP 1/16W R4627 1-218-965-11 RES, CHIP 1/16W 1-418-327-21 CHARGER, AC ADAPTOR (AC-VQ800) 1-418-732-21 REMOTE COMMANDER (RMT-DCM1) R4628 1-218-971-11 RES, CHIP...
Page 137 < PARTS REFERENCE SHEET > You can find the parts position of mount locations applying to MAIN board of a set. MAIN SIDE A DCM–M1 IC5002 IC8101 IC3004 IC5404 – DCM-M1...
Page 138 DCM-M1 Sony Corporation 1999L05044-1 9-927-635-11 Personal Audio Division Company Printed in Japan C 1999. 12 – 254 – Published by General Engineering Dept.
Page 139 DCM-M1 US Model Canadian Model SERVICE MANUAL E Model 2000. 03 SUPPLEMENT-1 File this supplement with the service manual. Subject: 1. Change of General 2. Correction of Schematic Diagram 3. Change of repair parts 4. Addition of the note about a special tool for ICs.
Page 140 Additional of the instruction manual for Argentina model. Page ACCESSORIES & PACKING MATERIALS Ref. No. Part No. Description Remark 6-21 3-866-152-31 MANUAL, INSTRUCTION (SPANISH) (Argentina) Sony Corporation 2000C05044-1D 9-927-635-81 Personal Audio Division Company Printed in Japan C 2000. 3 – 2 – Published by General Engineering Dept.
Page 141 DCM-M1 US Model Canadian Model SERVICE MANUAL E Model 2000. 05 SUPPLEMENT-2 File this supplement with the service manual. Subject: • Addition of Section 7 Adjustments • Correction of Schematic Diagrams...
Page 142 7. ADJUSTMENTS For the adjustment of this set, the test mode and the firmware data writing are provided. In the test mode, various adjustment, setting, and checking can be made. Also, the firmware data writing is executed when the Main board itself, or the Flash Memory (IC8005) or MPEG Control (IC8501) on the Main board is replaced.
Page 143: Test Mode
• MD1 High reflectance pre-mastered disc (TDYS-1) number display field Part code: 4-963-646-01 Test mode item name • MD1 MO disc display field Commercially available SONY MD1 MO disc Version display field (already recorded) Fig.7-1-2 • MD2 MO disc Commercially available SONY MD2 MO disc...
Page 144 4) Adjustment data and adjustment status display field 3. Switching of screen display For the items in which there are adjustment data, the data be- The LCD and EVF adjustment contains the items that require ing adjusted is displayed.In the EVF and LCD adjustment, if the screen display to be switched to the test signal screen.
Page 145: Evf System Adjustment
1-2. EVF System Adjustment [Connector for adjustment] The measurement points for EVF adjustment are concentrated on Note 1: The backlight (fluorescent tube) is driven with high volt- the CN4901 on the VF board. Connect a measuring instrument to age AC power. Accordingly, do not touch the backlight it via adjusting monitor jig (J-2503-017-A).
Page 146 1. EVF Adjustment Data Initializing 3. Brightness Adjustment Set the VIDEO signal level that drives the LCD (of EVF) to proper Item number 2-03-01 value. If deviated, the EVF screen will be unclear, black blurring, or white Screen display Test mode screen blurring.
Page 147 4. Contrast Adjustment 5. Backlight Consumed Current Adjustment Set the VIDEO signal level that drives the LCD to proper value. Set the brightness of backlight. If deviated, the EVF screen will be unclear, black blurring, or white If deviated, the picture will be too dark or too bright. blurring.
Page 148: Lcd System Adjustment
1-3. LCD System Adjustment [Connector for adjustment] The measurement points for LCD adjustment are concentrated on Note 1: The backlight (fluorescent tube) is driven with high volt- the CN4305 on the LCD board. age AC power. Accordingly, do not touch the backlight Connect a measuring instrument to it via adjusting monitor jig holder;...
Page 149 1. LCD Adjustment Data Initializing 3. Horizontal Position Adjustment Adjust the display position on LCD panel properly. Item number 3-03-01 Item number 3-01-02 Screen display Test mode screen Screen display Color bar Adjusting method Measurement point CH1: Adjusting monitor jig D pin 1) Select item number “3-03-01”.
Page 150 4. RGB D Range Adjustment 5. Brightness Adjustment Set the D range of RGB decoder driver step-wise output that drives Set the VIDEO signal level that drives the LCD to proper value. If deviated, the LCD screen will be unclear, black blurring, or white LCD to proper value.
Page 151 6. Contrast Adjustment 7. V-COM Level Adjustment Set the VIDEO signal level that drives the LCD to proper value. Set common electrode drive signal level of the LCD panel to proper If deviated, the LCD screen will be unclear, black blurring, or white value.
Page 152 8. Color Adjustment 9. V-COM Adjustment Set the color density to the specified value. Set DC bias of common electrode drive signals for the LCD panel If deviated, the color will be too dark or too light. to proper value. If deviated, the LCD screen will be unstable where flickering or Item number 3-01-07...
Page 153: Servo System Adjustment
• MD1 High reflectance pre-mastered disc (TDYS-1) Part code: 4-963-646-01 Adjustment data • MD1 MO disc initial value Commercially available SONY MD1 MO disc (already recorded) A = 66.0 ± 1.0 mV Adjustment value • MD2 MO disc Commercially available SONY MD2 MO disc Note: Use AC adapter whenever performing this adjustment.
Page 154 Faulty item checking method 1) From the adjustment status display screen at “NG” (Fig.7-1- 19), read a 2-digit number at part “A”. Example: On the following screen, if adjustment finished, “78” is displayed. TEST MODE made by MD dep. I TRON Ver.
Page 155 2. Mecha. Deck Block Primary Check Checking method The following parts of the mecha. deck block can be checked in a 1) In the normal mode, set the POWER switch to “CAMERA”. simple check. 2) Check that “DISC LID IS OPEN” is displayed on the LCD •...
Page 156: Mac Address Setting
1-5. MAC Address Setting 4) Operating the keys on the set, enter the Test mode. 5) Select the item “7-02-01” and press u key to activate the The MAC address must be unique in the world. Switch Check mode. On this set, hexadecimal MAC address is set for every serial num- Note: When the Switch Check mode becomes active, the ber of the set.
Page 157 0000 8192 2000 16384 4000 24576 6000 32768 8000 40960 A000 49152 C000 57344 E000 0100 8448 2100 16640 4100 24832 6100 33024 8100 41216 A100 49408 C100 57600 E100 0200 8704 2200 16896 4200 25088 6200 33280 8200 41472 A200 49664 C200...
Page 158 Hexadecimal-decimal Conversion Table Lower digit of hexadecimal Upper digit of hexadecimal Example: If decimal number is “53”, the higher digit 1 of hexadecimal number is “3” and the lower digit 2 is “5”, and thus “35” is the hexadecimal number to be obtained. Table 7-1-8 –...
Page 159 2. MAC Address Setting Method 1) Select the item number “7-01-01”. 2) Press u key to activate the MAC Address Set mode. (When the MAC Address Set mode becomes active, the MAC address is displayed as shown in Fig.7-1-24) TEST MODE made by MD dep.
Page 160: Touch Panel Adjustment
1-6. Touch Panel Adjustment 1. Touch Panel Position Alignment Touch Panel The touch panel position alignment should be made in both cases where the LCD screen is opened, and it is closed. Please Touch In touching the screen, use the input pen attached. Adjusting method 1) Select the item number “7-01-02”.
Page 161: Other Checking
1-7. Other Checking 2.Key Check In the Key Check mode, even pressing the x key cannot release 1. Switch Check the Key Check mode. To exit from this mode, turn the power off. In the Switch Check mode, even pressing the x key cannot re- lease the Switch Check mode.
Page 162 6) Check that the name associated with the pressed key is dis- 3. Adjustment Condition Check played at part if a key on the set is pressed. (See Table In the Adjustment Condition Check mode, current conditions of below) servo auto adjustment, MAC address setting, and touch panel po- sition alignment can Display Key name...
Page 163: Firmware Data Writing Method
7-2. Firmware Data Writing Method Write the data by the method given below, when the Main board or the Flash Memory (IC8005) and MPEG Control (IC8501) mounted on the MAIN board were replaced. 2-1. Preparation 1. Measuring Equipment To write the data, use measuring equipment listed below: 1) Personal computer (Windows95/98 installed) 2) Hyper Terminal (Communication software attached to the Win- dows)
Page 164 3. Hyper Terminal Setting 3) On the [Port Settings] screen, set the following and click [OK]. 1) Double-click [Hypertrm.exe] in the Hyper Terminal folder of Bits per second: 57600 the personal computer. Data bits: 8 2) On the [Connection Description] screen, enter the name “DCM- Parity: None M1”...
Page 165 4. Setting of the Set 5) On the [ASCII Setup] screen, set the following and click [OK]. [ASCII Sending] After the Hyper Terminal setting finished, check that the prompt Line delay: [2] milliseconds appears on the screen, and then perform a setting to the set through [ASCII Receiving] the steps given below.
Page 166: Writing To Flash Memory (Ic8005)
2-2. Writing to Flash Memory (IC8005) 2-3. Writing to MPEG Control (IC8501) Note 1: When the writing to the Flash Memory (IC8005) was Note 1: Hyper Terminal setting must already be finished. executed, perform the following: Note 2: on typical screen display indicates input characters. •...
Page 167 Board Check Monitor ver1.XXX > V << V850E Flash Writer menu V0.203 >> A ......V850E Auto sequence (Erase, Program,Verify) R ......V850E Device reset P ......V850E Program mode on I ......Initialize parameter L ......Load Motlora S format file W ......
Page 168 • Correction of Schematic Diagrams : Indicates changed portion. MAIN BOARD (1/8) (Page 4-29 to 4-30. Location A to E, 1 to 8) Incorrect Correct – 28 –...
Page 169 MAIN BOARD (3/8) (Page 4-32. Location E, 28) Incorrect Correct MAIN BOARD (3/8) (Page 4-32. Location J, 27 to 29) Incorrect Correct MAIN BOARD (3/8) (Page 4-39. Location C to E, 1 to 4) Incorrect Correct MAIN BOARD (3/8) (Page 4-39 to 40. Location E, 8 to 10) Incorrect Correct MAIN BOARD (3/8) (Page 4-40.
Page 170 MAIN BOARD (3/8) (Page 4-40. Location C, 15 to 19) Incorrect Correct MAIN BOARD (3/8) (Page 4-40. Location F to G, 17 to 18) Incorrect Correct MAIN BOARD (3/8) (Page 4-40. Location J to L, 15 to 18) Incorrect Correct MAIN BOARD (4/8) (Page 4-44.
Page 171 MAIN BOARD (4/8) (Page 4-44. Location D to E, 14 to 16) Incorrect Correct MAIN BOARD (4/8) (Page 4-44 to 45. Location J to L, 17 to 19) Incorrect Correct MAIN BOARD (4/8) (Page 4-45. Location H to J, 24 to 27) Incorrect Correct MAIN BOARD (4/8) (Page 4-46.
Page 172 MAIN BOARD (5/8) (Page 4-48. Location F to G, 1 to 4) Incorrect Correct MAIN BOARD (8/8) (Page 4-59. Location L, 1 to 4) Incorrect Correct CLV BOARD (Page 4-77. Location G to H, 12 to 14) Incorrect Correct REC BOARD (Page 4-82. Location D to E, 10 to 12) Incorrect Correct –...
Page 173 DCM-M1 • Signal Paths were Missing in Service Manual. LCD (LCD) SCHEMATIC DIAGRAM (Page 4-106 to 4-108) – 33 – – 34 – – 35 –...
Page 174 DCM-M1 ETHER BOARD (Page 4-116. Location D, 1 to 3) Incorrect Correct Sony Corporation 2000E05035-1 9-927-635-82 Audio Entertainment Group Printed in Japan C 2000. 5 – 38 – Published by PE General Engineering Dept.
Page 175 DCM-M1 US Model Canadian Model SERVICE MANUAL E Model 2000. 08 SUPPLEMENT-3 File this supplement with the service manual. Subject: • Addition of Section 7 Camera Section Adjustment • Correction of Schematic Diagrams...
Page 176 7-3. CAMERA SECTION ADJUSTMENT TABLE OF CONTENTS 3-1. Preparation before Adjustment 3-3. Camera System Adjustment ........3 ........8 3-1-1. Service Tools List ............3 Zoom Center Adjustment ..........8 3-1-2. Preparation ..............4 Hall Adjustment ............... 8 3-1-3. Precautions ..............5 Flange Back Adjustment (Using flange back adjusting chart subject more than 500 m away) .....
Page 177: Preparation Before Adjustment
3-1. Preparation before Adjustment 3-1-1. Service Tools List • Oscilloscope • Color Monitor • Vectorscope • Regulated Power Supply • Digital Voltmeter Ref. No. Name Part Code Usage Auto white balance adj./check Filter for color temperature correction (C14) J-6080-058-A White balance adj./check ND filter 1.0 J-6080-808-A White balance check...
Page 178 3-1-2. Preparation Pattern box Note 1: See “DISASSEMBLY” for removing the cabinet and each board. Note 2: The lens block and each board need not be separated, if only the adjustment is performed. Note 3: For the power supply, use exclusive AC adapter. about 1.5m Front side of the lens Fig.
Page 179 3-1-3. Precautions 1. Switch setting Set the switches to the following positions respectively and per- form the adjustment without loading a disc, unless otherwise speci- fied. 1. POWER switch ............CAMERA 2. DIGITAL ZOOM (MENU screen) ......OFF 3. STEADY SHOT (MENU screen) ......OFF 4.
Page 180: Service Mode
3-2. Operation during Adjustment 1) Version display field The versions of respective programs that compose the set are In adjusting the camera, execute the service mode in the Test Mode. displayed. Note: For the adjustment items that must be checked with the color ITON ....
Page 181 3-2-4. Key Operation in Test Mode 2. Change or writing of camera register In the Test mode, use the keys on the set for operation. (Operation in Service mode) • Cursor movement (., > keys) For adjusting the camera, execute the test mode item “1-02-01” (major item: Camera, medium item: Adjust, and minor item: Ser- vice mode) to select the Service mode and perform adjustment Moves the cursor by .
Page 182 3-3. Camera System Adjustment 1. Zoom Center Adjustment Adjust the center voltage of Zoom control to the center of microcomputer A/D value. If deviated, zooming will be executed even with the Zoom control in center position. Subject Arbitrary Measurement point Display data of page: 06, address: 50 Adjustment page Adjustment address...
Page 183: Flange Back Adjustment (Using Flange Back Adjusting Chart Subject More Than 500 M Away)
3. Flange Back Adjustment (Using flange back adjusting chart subject more than 500 m away) The flange back adjustment of the inner focus lens is carried out automatically. If deviated, auto focus and manual focus will be disordered. Flange back adjustment (1) Flange back adjusting chart (Located at 2.00 m position from lens front surface) Subject...
Page 184 Flange back adjustment (2) Subject more than 500 m away Subject (which should be clear contrast such as a building) Measurement point Check operation on monitor TV Measuring instrument (Camera-through screen) Adjustment page Adjustment address 24 – 29, 36 – 3D Note: For the data display, the data at the time when address was set is displayed, and it is not updated.
Page 185: Flange Back Adjustment (Using Mini Pattern Box)
4. Flange Back Adjustment (Using mini pattern box) The flange back adjustment of the inner focus lens is carried out automatically. If deviated, auto focus and manual focus will be disordered. Mini pattern box with ND filter Subject Siemens star chart (Note 1) Measurement point Check operation on monitor TV Measuring instrument...
Page 186: Flange Back Check
5. Flange Back Check Siemens star (reflection type) Subject (Located at 2.00 m position from lens front surface) (Luminance: about 200 lux) Measurement point Check on monitor TV Measuring instrument (Camera-through screen) Adjustment value Focus must be in order at TELE end and WIDE end Switch setting 1) DIGITAL ZOOM (Menu screen) ..
Page 187: Optical Axis Adjustment
6. Optical Axis Adjustment Correct the deviation of optical axis between lens and CCD imager. If deviated, the center of screen will be shifted when the zoom is moved from TELE end to WIDE end. Subject Siemens star (reflection type) Measurement point Check on monitor TV Measuring instrument...
Page 188 Adjusting method Steps Page Address Data Work Description Press the y key. Press the y key. Press the y key. Place the Siemens star at 2.0 m forward position from the lens front surface. Shoot the Siemens star with the zoom at TELE end. Adjusting the lens direction, make the center of Siemens star and the center of optical axis deviation specification frame (monitor screen) concurrent.
Page 189: Agc Gain Calibration Adjustment
7. AGC Gain Calibration Adjustment Clear chart (PTB-450) Subject (Color reproduction adjusting frame) Adjustment page Adjustment address 3A – 3D Note: For the data display, the data at the time when address was set is displayed, and it is not updated. Check data variation while repeating address change and resetting (change address from “02”...
Page 190: Color Reproduction Adjustment
8 Color Reproduction Adjustment Adjust the primary color separation matrix factor so that colors are reproduced correctly. If deviated, colors are not reproduced correctly. Color bar chart (PTB-450) Subject (Color reproduction adjusting frame) VIDEO terminal of VIDEO/AUDIO terminals Measuring point (Camera-through screen) Measuring instrument Vectorscope...
Page 191: Max. Gain Adjustment
9. Max. Gain Adjustment Set the lowest subject illuminance. If deviated, necessary video level will not be got in low illuminance environment. Clear chart (PTB-450) Subject (Color reproduction adjusting frame) Adjustment page Adjustment address Note: For the data display, the data at the time when address was set is displayed, and it is not updated. Check data variation while repeating address change and resetting (change address from “02”...
Page 192: Auto White Balance & Lv Reference Data Acquisition
10. Auto White Balance & LV Reference Data Acquisition Clear chart (PTB-450) Subject (Color reproduction adjusting frame) Adjustment page Adjustment address 20 – 23, 3E, 3F Note 1: Color Reproduction Adjustment must be already finished. Note 2: The auto white balance & LV reference data acquisition is available only once after the power is turned on. Turn the power off, then on again if the data acquisition is retried.
Page 193: Auto White Balance Check
12. Auto White Balance Check Clear chart (PTB-450) Subject (Color reproduction adjusting frame) Color temperature correction filter C14 Filter ND filter 1.0 and 0.3 VIDEO terminal of VIDEO/AUDIO terminals Measurement point (Camera-through screen) Measuring instrument Vectorscope Adjustment value Fig. 7-3-15 (A) – (C) Checking method Page Address...
Page 194 • Correction of Schematic Diagrams : Indicates changed portion. MAIN BOARD (4/8) (Page 4-44. Location B to C, 14 to 16) Incorrect Correct MAIN BOARD (5/8) (Page 4-52. Location A to B, 37 to 39) Incorrect Correct MAIN BOARD (6/8) (Page 4-53. Location A to E, 5 to 8) Incorrect Correct –...
Page 195 VF BOARD (2/3) (Page 4-90. Location I to J, 30 to 32) Incorrect Correct ETHER BOARD (Page 4-117. Location B to D, 6 to 9) Incorrect Correct – 21 –...
Page 196 FOR CAMERA OPTICAL AXIS ADJUSTMENT 337.5 22.5 292.5 67.5 247.5 112.5 202.5 157.5 – 22 –...
Page 197 FOR CAMERA COLOR REPRODUCTION ADJUSTMENT Take a copy of CAMERA COLOR REPRODUCTION FRAME with a clear sheet for use. DCM-M1 – 23 –...
Page 198 CDM-M1 Sony Corporation 2000H05035-1 9-927-635-83 Audio Entertainment Group Printed in Japan C 2000. 8 Published by General Engineering Dept.

Sony DCM-M1 Service Manual

Table of Contents

1 General

2 Disassembly

3 Block Diagrams

6 Electrical Parts List

7. Adjustments

7-3. Camera Section Adjustment

Quick Links

Chapters

Related Manuals for Sony DCM-M1

Summary of Contents for Sony DCM-M1

Table of Contents