Page 4
RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to the GSA ADP Schedule contract with Lenovo Group Limited, if any, or the standard terms of this commercial license, or if the agency is unable to accept this Program under these terms, then we provide this Program under the provisions set forth in Commercial Computer Software–Restricted Rights at FAR 52.227-19, when applicable, or under Rights in...
Page 6
. 68 Access Help . . 60 Safety and warranty . 60 Appendix B. Notices ..71 www.lenovo.com . 60 Television output notice . . 72 Help and service . 60 Trademarks .
Note: If you notice these conditions with a product (such as an extension cord) that is not manufactured for or by Lenovo, stop using that product until you can contact the product manufacturer for further instructions, or until you get a suitable replacement.
Danger Hazardous moving parts. Keep fingers and other body parts away. Attention Before replacing any CRUs, turn off the computer and wait three to five minutes to let the computer cool before opening the cover. Static electricity prevention Static electricity, although harmless to you, can seriously damage computer components and options.
The power cords shall be safety approved. For Germany, it shall be H05VV-F, 3G, 0.75 mm , or better. For other countries, the suitable types shall be used accordingly. Never wrap a power cord around a power adapter or other object. Doing so can stress the cord in ways that can cause the cord to fray, crack, or crimp.
In addition, many mobile products, such as notebook computers, utilize a rechargeable battery pack to provide system power when in portable mode. Batteries supplied by Lenovo for use with your product have been tested for compatibility and should only be replaced with approved parts.
v Do not operate your computer or charge the battery near flammable materials or in explosive environments. v Ventilation slots, fans, and/or heat sinks are provided with the product for safety, comfort, and reliable operation. These features might inadvertently become blocked by placing the product on a bed, sofa, carpet, or other flexible surface.
Electrical current safety information Danger Electrical current from power, telephone, and communication cables is hazardous. To avoid a shock hazard: v To prevent possible shock hazard, do not use your computer during a lightning storm. v Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm.
Perchlorate material: Special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate. Modem safety information Caution To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord. To reduce the risk of fire, electrical shock, or injury when using telephone equipment, always follow basic safety precautions, such as: v Never install telephone wiring during a lightning storm.
Power supply statement Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no serviceable parts inside these components. If you suspect a problem with one of these parts, contact a service technician.
Chapter 8, “Getting information, help, and service,” on page 59 provides information about the wide variety of helpful resources available from Lenovo. v Appendix A, “Manual modem commands,” on page 63 provides commands for manually programming your modem.
Where it is impossible to avoid reflections or to adjust the lighting, an antiglare filter placed over the screen might be helpful. However, these filters might affect the clarity of the image on the screen; try them only after you have exhausted other methods of reducing glare.
Page 22
Note: Some models will have keyboards with a fingerprint reader. After you setup and turn on your computer, refer to the Access Help online help system for information about your fingerprint reader. See “Access Help” on page 60 for instructions on how to open the online help system.
Page 23
5. If you have a modem, connect the modem using the following information. L IN L I N L I N L IN This illustration shows the two connections on the back of the computer that are needed to set up your modem. In the United States and other countries or regions that use the RJ-11 telephone outlet, attach one end of the telephone cable to the telephone and the other end to the telephone connector on the back of the computer.
Page 24
7. If you have powered speakers with an ac adapter, use the following instructions. a. Connect the cable that runs between the speakers, if necessary. On some speakers, this cable is permanently attached. b. Connect the ac adapter cable to the speaker. c.
1 USB Use this connector to attach a device that requires a USB connection, such as a keyboard, mouse, scanner, printer, or personal digital assistant (PDA). 2 Serial Use this connector to attach an external modem, serial printer, or other device that uses a 9-pin serial connector. 3 S-video Use this connector to attach a television set that has an S-Video connector.
Finishing the software installation Important Read the license agreements carefully before using the programs on this computer. These agreements detail your rights, obligations, and warranties for the software on this computer. By using these programs, you accept the terms of the agreements. If you do not accept the agreements, do not use the programs.
Your computer comes with antivirus software you can use to detect and eliminate viruses. Lenovo provides a full version of antivirus software on your hard disk with a free 90-day subscription. After 90 days, you must get a new virus definition.
Page 30
v Intel Pentium 4 processor ® v Intel Celeron D processor v AMD Athlon 64 v AMD Sempron v Internal cache (size varies by model type) Memory v Support for two double data rate 2 (DDR2) dual inline memory modules (DIMMs) v 512 KB flash memory for system programs Internal drives...
Page 31
1. The operating systems listed here are being certified or tested for compatibility at the time this publication goes to press. Additional operating systems might be identified by Lenovo as compatible with your computer following the publication of this booklet. Corrections and additions to this list are subject to change. To determine if an operating system has been certified or tested for compatibility, check the Web site of the operating system vendor.
Specifications This section lists the physical specifications for your computer. Dimensions Height: 400 mm (15.7 in.) Width: 175 mm (6.9 in.) Depth: 432 mm (17.0 in.) Weight Minimum configuration: 8.17 kg (18 lb) Maximum configuration: 10.21 kg (22.5 lb) Environment Air temperature: System on: 10°...
- Optical drives, such as CD and DVD drives - Hard disk drive - Diskette drives and other removable media drives For the latest information about available options, see the Lenovo Web site at http://www.lenovo.com or contact your reseller or marketing representative. Tools required To install some options in your computer, you might need a flat-blade or Phillips screwdriver.
Handling static-sensitive devices Static electricity, although harmless to you, can seriously damage computer components and options. When you add an option, do not open the static-protective package containing the option until you are instructed to do so. When you handle options and other computer components, take these precautions to avoid static electricity damage: v Limit your movement.
Locating the connectors on the front of your computer The following illustration shows the locations of the connectors on the front of the computer. USB connector Microphone connector Headphone connector USB connector Chapter 3. Installing options...
Locating the connectors on the rear of your computer The following illustration shows the locations of the connectors on the rear of the computer. Power supply diagnostic Ethernet connector LEDs Voltage selection switch USB connectors (2) Power connector Microphone connector Standard mouse connector Audio line out connector Standard keyboard connector...
Obtaining device drivers You can obtain device drivers for operating systems that are not preinstalled at http://www.lenovo.com/support/ on the World Wide Web. Installation instructions are provided in README files with the device-driver files. Chapter 3. Installing options...
Removing the cover Important Read “Important safety information” on page v“Important safety information” on page v and “Handling static-sensitive devices” on page 16 before removing the computer cover. To remove the computer cover: 1. Remove any media (diskettes, CDs, or tapes) from the drives, shut down your operating system, and turn off all attached devices and the computer.
Locating components The following illustration will help you locate the various components in your computer. Microprocessor fan and heat sink PCI Express and PCI adapter connectors Memory modules System fan PCI adapter card Power supply Chapter 3. Installing options...
Identifying parts on the system board The system board (sometimes called the planar or motherboard) is the main circuit board in your computer. It provides basic computer functions and supports a variety of devices that are factory-installed or that you can install later. The following illustration shows the locations of parts on the system board (some models).
Page 41
The following illustration shows the locations of parts on the system board (some models). Microprocessor and heat sink Front USB connectors (2) Microprocessor fan connector Serial (COM) connector Memory connector 1 Front audio connector Memory connector 2 CD-IN connector Power connector PCI adapter connectors (2) Diskette drive connector PCI Express x1 adapter connector...
Page 42
The following illustration shows the locations of parts on the system board (some models). Microprocessor and heat sink Front panel connector Microprocessor fan connector Front panel USB connectors (2) Memory connector 1 Front audio connector Memory connector 2 CD-IN connector Diskette drive connector PCI adapter connectors Power connector...
Installing memory Your computer has two connectors for installing dual inline memory modules (DIMMs) that provide up to a maximum of 4.0 GB of system memory. When installing memory modules, the following rules apply: v Use 1.8 V, 240-pin double data rate 2 synchronous dynamic random access memory (DDR2 SDRAM).
Installing adapters This section provides information and instructions for installing and removing adapters. Your computer has two expansion connectors for PCI adapters and one for a PCI Express x1 adapter. To install an adapter: 1. Remove the computer cover. See “Removing the cover” on page 20. 2.
Page 45
5. Pivot the adapter latch to the closed position to secure the adapters. What to do next v To work with another option, go to the appropriate section. v To complete the installation, go to “Replacing the cover and connecting the cables”...
Installing internal drives This section provides information and instructions for installing and removing internal drives. Internal drives are devices that your computer uses to read and store data. You can add drives to your computer to increase storage capacity and to enable your computer to read other types of media.
Page 47
The following illustration shows the locations of the drive bays. The following list describes the types and size of drives you can install in each bay: 1 Bay 1 - Maximum height: 43.0 mm (1.7 in.) v Optical drive such as CD drive or DVD drive (preinstalled in some models) v 5.25-inch hard disk drive v 3.5-inch hard disk drive (requires a...
Installing a drive in bay 1 or bay 2 To install a drive in bay 1 or bay 2, follow these steps: 1. Remove the computer cover. See “Removing the cover” on page 20. 2. Remove the front bezel by releasing the three plastic tabs on the left side and pivoting the bezel outward.
Page 49
7. For a 5.25-inch drive, install a retainer bracket on the side of the drive. 8. For a 3.5-inch drive, you must use a Universal Adapter Bracket, 5.25 to 3.5-inch. You can obtain a Universal Adapter Bracket, 5.25 to 3.5-inch from a local computer retailer or by contacting the Customer Support Center.
Connecting drives The steps to connect a drive are different depending on the type of drive. Use one of the following procedures for your drive connection. Connecting the first optical drive 1. The drive requires two cables; a power cable that connects to the power supply and a signal cable that connects to the system board.
Connecting a serial ATA hard disk drive A serial hard disk drive can be connected to any available SATA connector. 1. Locate the signal cable that comes with the new drive. 2. Locate an available SATA connector on the system board. See “Identifying parts on the system board”...
The cable lock also locks the buttons used to open the computer cover. This is the same type of lock used with many laptop computers. You can order a security cable directly from Lenovo. Go to http://www.lenovo.com/support/ and search on Kensington.
Padlock Your computer is equipped with a padlock loop such that the cover cannot be removed when a padlock is installed. Password protection To deter unauthorized use of your computer, you can use the Setup Utility program to set passwords. See “Using passwords” on page 47. What to do next v To work with another option, go to the appropriate section.
To change the battery: 1. Turn off the computer and all attached devices. 2. Remove the computer cover. See “Removing the cover” on page 20. 3. Locate the battery. See “Identifying parts on the system board” on page 22. 4. Remove the old battery. 5.
8. Move the jumper back to the standard (pins 1 and 2). 9. Replace the computer cover and connect the power cord. See “Replacing the cover and connecting the cables.” Replacing the cover and connecting the cables After working with options, you need to install any removed parts, replace the computer cover, and reconnect any cables, including telephone lines and power cords.
This chapter will help you become familiar with recovery solutions provided by Lenovo. This chapter explains how and when to use the following recovery methods: v Creating and using Product Recovery discs...
v Windows Vista: Use Product Recovery discs to restore your computer to the original factory contents only. When using Product Recovery discs on Windows XP, you are given the option to enter the Rescue and Recovery workspace and choose from a variety of recovery operations.
v On a protected area of your hard disk v On a second hard disk installed in your computer v On an externally attached USB hard disk v On a network drive v On recordable CDs or DVDs (a recordable CD or DVD drive is required for this option) After you have backed up your hard disk, you can restore the complete contents of the hard disk, restore selected files only, or restore only the Windows operating...
multiple partitions on your hard disk, you have the option to restore the factory contents to the C: partition and leave the other partitions intact. Because the Rescue and Recovery workspace operates independently from the Windows operating system, you can restore the factory contents even if you cannot start the Windows operating system.
1. Start your computer and operating system. 2. Using an Internet browser, go to the following Web address: http://www.lenovo.com/think/support/site.wss/document.do?lndocid=MIGR-54483 3. Insert a diskette into diskette drive A. Information on the diskette will be erased and the diskette will be formatted appropriately.
The latest device drivers for factory-installed devices also are available on the World Wide Web at http://www.lenovo.com/think/support/. To reinstall a device driver for a factory-installed device, do the following: 1. Start your computer and operating system.
Setting a rescue device in the startup sequence Before you start the Rescue and Recovery program from a CD, DVD, USB hard disk drive, or any external device, you must first change the startup sequence in the Setup Utility. To view or change the startup sequence, do the following: 1.
v Have at least eight characters in length v Contain at least one alphabetic character, one numeric character, and one symbol v Contain at least one of the following symbols: , . / ` ; ' [] v You can also use the space bar v Setup Utility program and hard disk drive passwords are not case sensitive v Not be your name or your user name v Not be a common word or a common name...
To set Security Profile by Device, do the following: 1. Start the Setup Utility program (see “Starting the Setup Utility program” on page 47). 2. From the Setup Utility program menu, select Security. 3. Select Security Profile by Device. 4. Select the desired devices and settings and press Enter. 5.
Advanced settings On some computer models the Advanced settings menu includes a setting to Enable/Disable HyperThreading. This feature works only with HyperThreading-aware operating systems, such as Microsoft Windows XP. The default setting for HyperThreading is Enabled. However, if you select Set Defaults and are using an operating system other than Windows XP, your computer performance might be degraded.
Lenovo might make changes and enhancements to the POST/BIOS. When updates are released, they are available as downloadable files on the Lenovo Web site at http://www.lenovo.com. Instructions for using the POST/BIOS updates are available in a .txt file that is included with the update files. For most models, you can download either an update program to create a system-program-update (flash) diskette or an update program that can be run from the operating system.
Notes: 1. You can download the latest version of the PC-Doctor for Windows and PC-Doctor for DOS diagnostic programs from http://www.lenovo.com/ support/. Type your machine type into the Use Quick Path field and click Go to find the downloadable files that are specific to your computer.
PC-Doctor for DOS Depending upon your machine type and model, you either have PC-Doctor for DOS or PC-Doctor for Windows PE on your Lenovo computer. The PC-Doctor for DOS diagnostic program is part of the Rescue and Recovery workspace and runs independently of the Windows operating system. Use PC-Doctor for DOS, if you are unable to start the Windows operating system or if PC-Doctor for Windows has not been successful in isolating a possible problem.
Page 74
3. Repeatedly press and release the F11 key as you turn on the computer. 4. When you hear beeps or see a logo screen, stop pressing the F11 key. The Rescue and Recovery workspace opens. Note: For some models, press the Esc key to enter Rescue and Recovery. 5.
PC-Doctor for Windows PE Depending upon your machine type and model, you either have PC-Doctor for DOS or PC-Doctor for Windows PE on your Lenovo computer. The PC-Doctor for Windows PE diagnostic program is part of the Rescue and Recovery workspace.
Page 76
Note: The following illustration might be slightly different from your mouse. 1 Retainer ring 2 Ball 3 Plastic rollers 4 Ball cage To clean a mouse with a ball, follow the instructions below: 1. Turn off your computer. 2. Disconnect the mouse cable from the computer. 3.
Chapter 8. Getting information, help, and service If you need help, service, or technical assistance or just want more information about products manufactured by Lenovo, you will find a wide variety of sources available from Lenovo to assist you. Information resources This section provides information on how to access useful resources relating to your computing needs.
The Lenovo Web site (www.lenovo.com) provides an extensive amount of information and services to help you buy, upgrade, and maintain your computer. You can access the most up-to-date information for your computer on the Lenovo Web site. From the www.lenovo.com Web site, you can also: v Shop for desktop and notebook computers, monitors, projectors, upgrades and accessories for your computer, and special offers.
Engineering Change management - Occasionally, there might be changes that are required after a product has been sold. Lenovo or your reseller, if authorized by Lenovo, will make selected Engineering Changes (ECs) available that apply to your hardware.
Service availability and service name might vary by country or region. For more information about these services, go to the Lenovo Web site at http://www.lenovo.com. User Guide...
Page 82
Command Function Force modem off-hook (make busy) Note: H1 command is not supported for Italy Display product-identification code Factory ROM checksum test Internal memory test Firmware ID Reserved ID Low speaker volume Low speaker volume Medium speaker volume High speaker volume Internal speaker off Internal speaker on until carrier detected Internal speaker always on...
Extended AT commands Command Function &C_ &C0 Force Carrier Detect Signal High (ON) &C1 Turn on CD when remote carrier is present &D0 &D_ Modem ignores the DTR signal &D1 Modem returns to Command Mode after DTR toggle &D2 Modem hangs up, returns to the Command Mode after DTR toggle &D3 Resets modem after DTR toggle...
Command Function &V1 Display Last Connection Statistics &W_ &W0 Stores the active profile as Profile 0 &W1 Stores the active profile as Profile 1 Disable auto-retrain Enable auto-retrain +MS? Displays the current Select Modulation settings +MS=? Displays a list of supported Select Modulation options +MS=a,b,c,e,f Select modulation where: a=0, 1, 2, 3, 9, 10, 11,...
Fax Class 1 commands +FAE=n Data/Fax Auto Answer +FCLASS=n Service Class +FRH=n Receive data with HDLC framing Receive data +FRM=n +FRS=n Receive silence +FTH=n Transmit data with HDLC framing +FTM=n Transmit data +FTS=n Stop transmission and wait Fax Class 2 commands +FCLASS=n Services class.
+FPHCTO Phase C time out. +FPOLL Indicates polling request. +FPTS: Page transfer status. +FPTS= Page transfer status. +FREV? Identify revision. +FSPT Enable polling. +FTSI: Report the transmit station ID. Voice commands Select Baud Rate #BDR #CID Enable Caller ID detection and reporting format Select Data, Fax or Voice/Audio #CLS #MDL?
Page 87
Attention Switzerland User: If your Swisscom phone line does not have Taxsignal switched OFF, modem function may be impaired. The impairment may be resolved by a filter with the following specifications: Telekom PTT SCR-BE Taximpulssperrfilter-12kHz PTT Art. 444.112.7 Bakom 93.0291.Z.N Appendix A.
Macrovision Corporation. Reverse engineering or disassembly is prohibited. Trademarks The following terms are trademarks of Lenovo in the United States, other countries, or both: Lenovo Rescue and Recovery...