hit counter script
HP ProLiant DL385 G5p Maintenance And Service Manual
  1. Manuals
  2. Brands
  3. HP Manuals
  4. Server
  5. ProLiant DL385 G5p
  6. Maintenance and service manual

HP ProLiant DL385 G5p Maintenance And Service Manual

Hide thumbs Also See for ProLiant DL385 G5p:
Table of Contents

Advertisement

Quick Links

Download this manual
HP ProLiant DL385 G5p Server
Maintenance and Service Guide
Abstract
This guide describes identification and maintenance procedures, diagnostic tools, specifications and requirements for hardware components and
software. This guide is for an experienced service technician. HP assumes you are qualified in the servicing of computer equipment, trained in
recognizing hazards in products, and are familiar with weight and stability precautions.
Part Number: 495671-004
April 2012
Edition: 4

Advertisement

Table of Contents
loading

Related Manuals for HP ProLiant DL385 G5p

Summary of Contents for HP ProLiant DL385 G5p

  • Page 1 This guide describes identification and maintenance procedures, diagnostic tools, specifications and requirements for hardware components and software. This guide is for an experienced service technician. HP assumes you are qualified in the servicing of computer equipment, trained in recognizing hazards in products, and are familiar with weight and stability precautions.
  • Page 2 © Copyright 2008, 2012 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.

  • Page 3: Table Of Contents

    Remove the server from the rack ...................... 27 Access the product rear panel ......................27 Hot-plug power supply ........................28 HP Trusted Platform Module ........................30 Access panel ............................30 SAS hard drive blank ..........................30 Hot-plug SAS hard drive ........................... 31 Power supply blank ..........................
  • Page 4 Integrated Management Log ........................64 Integrated Lights-Out 2 technology ......................64 Option ROM Configuration for Arrays ....................... 64 HP ProLiant Essentials Rapid Deployment Pack .................... 65 HP ROM-Based Setup Utility ........................65 SmartStart software ..........................65 ROMPaq utility ..........................66 System Online ROM flash component utility ..................

  • Page 5: Customer Self Repair

    HP specifies in the materials shipped with a replacement CSR part whether a defective part must be returned to HP. In cases where it is required to return the defective part to HP, you must ship the defective part back to HP within a defined period of time, normally five (5) business days. The defective part must be returned with the associated documentation in the provided shipping material.
  • Page 6 HP sono realizzati con numerosi componenti che possono essere riparati direttamente dal cliente (CSR, Customer Self Repair). Se in fase di diagnostica HP (o un centro di servizi o di assistenza HP) identifica il guasto come riparabile mediante un ricambio CSR, HP lo spedirà direttamente al cliente per la sostituzione.
  • Page 7 La mancata restituzione del componente può comportare la fatturazione del ricambio da parte di HP. Nel caso di riparazione da parte del cliente, HP sostiene tutte le spese di spedizione e resa e sceglie il corriere/vettore da utilizzare.
  • Page 8 Si, durante la fase de diagnóstico, HP (o los proveedores o socios de servicio de HP) identifica que una reparación puede llevarse a cabo mediante el uso de un componente CSR, HP le enviará dicho componente directamente para que realice su sustitución. Los componentes CSR se clasifican en dos categorías:...
  • Page 9 HP podrá cobrarle por el de sustitución. En el caso de todas sustituciones que lleve a cabo el cliente, HP se hará cargo de todos los gastos de envío y devolución de componentes y escogerá la empresa de transporte que se utilice para dicho servicio.
  • Page 10 Opcional – Peças cujo reparo feito pelo cliente é opcional. Essas peças também são projetadas para o reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode haver ou não a cobrança de taxa adicional, dependendo do tipo de serviço de garantia destinado ao produto.
  • Page 11 No caso desse serviço, a substituição de peças CSR é obrigatória. Se desejar que a HP substitua essas peças, serão cobradas as despesas de transporte e mão-de-obra do serviço. Customer self repair 11...
  • Page 12 Customer self repair 12...
  • Page 13 Customer self repair 13...
  • Page 14 Customer self repair 14...
  • Page 15 Customer self repair 15...

  • Page 16: Illustrated Parts Catalog

    Illustrated parts catalog Mechanical components Item Description Assembly part Spare part Customer number number self repair (on page 5) Access panel 463177-001 507685-001 Mandatory Air baffle 463181-001 496061-001 Mandatory Hardware kit — 496058-001 Mandatory a) Fan blank 507009-001 — — b) Optical blank 505953-001 —...
  • Page 17 Optional—Parts for which customer self repair is optional. These parts are also designed for customer self repair. If, however, you require that HP replace them for you, there may or may not be additional charges, depending on the type of warranty service designated for your product.
  • Page 18 Optional: Opcional—Peças cujo reparo feito pelo cliente é opcional. Essas peças também são projetadas para o reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode haver ou não a cobrança de taxa adicional, dependendo do tipo de serviço de garantia destinado ao produto.

  • Page 19: System Components

    System components Item Description Assembly part Spare part Customer number number self repair (on page 5) System components Hot-plug fan 463172-001 496066-001 Mandatory Hot-plug power supply, 1200-W 490594-001 498152-001 Mandatory PCI riser cage, with non-hot-plug PCIe riser 463170-001 496060-001 Optional Optical drive cage 463175-001 496076-001...
  • Page 20 Item Description Assembly part Spare part Customer number number self repair (on page 5) System board assembly 488896-001 507686-001 Optional Power supply backplane 462954-001 496062-001 Optional Hard drive backplane — — — a) SAS backplane 451283-001 507690-001 Optional b) 6-bay hard drive backplane* 457174-001 496079-001 Optional...
  • Page 21 Optional—Parts for which customer self repair is optional. These parts are also designed for customer self repair. If, however, you require that HP replace them for you, there may or may not be additional charges, depending on the type of warranty service designated for your product.
  • Page 22 Optional: Opcional—Peças cujo reparo feito pelo cliente é opcional. Essas peças também são projetadas para o reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode haver ou não a cobrança de taxa adicional, dependendo do tipo de serviço de garantia destinado ao produto.
  • Page 23 Illustrated parts catalog 23...

  • Page 24: Removal And Replacement Procedures

    Required tools You need the following items for some procedures: • T-10/T-15 Torx screwdriver (provided inside the server) • HP Insight Diagnostics software ("HP Insight Diagnostics" on page 66) Safety considerations Before performing service procedures, review all the safety information.

  • Page 25: Preparation Procedures

    Extend the server from the rack (on page 25). If you are performing service procedures in an HP, Compaq branded, telco, or third-party rack cabinet, you can use the locking feature of the rack rails to support the server and gain access to internal components.

  • Page 26: Power Down The Server

    After performing the installation or maintenance procedure, slide the server back into the rack, and then press the server firmly into the rack to secure it in place. WARNING: To reduce the risk of personal injury, be careful when pressing the server rail-release latches and sliding the server into the rack.

  • Page 27: Remove The Server From The Rack

    Remove the server from the rack To remove the server from an HP, Compaq branded, telco, or third-party rack: Power down the server (on page 26). Extend the server from the rack (on page 25). Disconnect the cabling and remove the server from the rack. For more information, refer to the documentation that ships with the rack mounting option.

  • Page 28: Hot-Plug Power Supply

    Open the cable management arm. Cable management arm with right-hand swing NOTE: To access some components, you may need to remove the cable management arm. To access the product rear panel components, open the cable management arm: Power down the server (on page 26). Swing open the cable management arm.
  • Page 29 WARNING: To reduce the risk of personal injury from hot surfaces, allow the power supply or power supply blank to cool before touching it. CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless all bays are populated with either a component or a blank. To remove the component: Determine how many hot-plug power supplies are installed: If only one hot-plug power supply is installed, power down and remove the power cord from the...

  • Page 30: Hp Trusted Platform Module

    If you suspect a TPM board failure, leave the TPM installed and remove the system board ("System board" on page 56). Contact an HP authorized service provider for a replacement system board and TPM board. Access panel WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components to cool before touching them.

  • Page 31: Hot-Plug Sas Hard Drive

    Remove the component as indicated. To replace the blank, slide the blank into the bay until it locks into place. Hot-plug SAS hard drive To remove the component: CAUTION: For proper cooling do not operate the server without the access panel, baffles, expansion slot covers, or blanks installed.

  • Page 32: Optical Drive Cage

    To replace the component, reverse the removal procedure. Optical drive cage To remove the component: CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless all bays are populated with either a component or a blank. Power down the server (on page 26).

  • Page 33: Systems Insight Display

    To replace the component, reverse the removal procedure. Systems Insight Display To remove the component: Power down the server (on page 26). Extend the server from the rack (on page 25). Remove the access panel ("Access panel" on page 30). Remove the PCI riser cage ("PCI riser cage"...

  • Page 34: Front Left Bezel

    Remove the three T-10 Torx screws, and then detach the front bezel. To replace the component, reverse the removal procedure. Front left bezel To remove the component: Power down the server (on page 26). Extend or remove the server from the rack ("Remove the server from the rack"...

  • Page 35: Power Supply Backplane

    Remove the three T-10 Torx screws, and then detach the front bezel. To replace the component, reverse the removal procedure. Power supply backplane To remove the component: Power down the server (on page 26). Remove all power supplies ("Hot-plug power supply"...

  • Page 36: Hot-Plug Fan

    Hot-plug fan The server supports variable fan speeds. The fans operate at minimum speed until a temperature change requires a fan speed increase to cool the server. The server shuts down in the following temperature-related scenarios: • At POST: The BIOS suspends the server for 5 minutes if it detects a cautionary temperature level. If the cautionary temperature level is still detected after 5 minutes, the BIOS performs an orderly shutdown and enters Standby mode.

  • Page 37: Hard Drive Backplane

    Remove the fan. CAUTION: Do not operate the server for long periods with the access panel open or removed. Operating the server in this manner results in improper airflow and improper cooling that can lead to thermal damage. To replace the component, reverse the removal procedure. Hard drive backplane To remove the component: Power down the server (on page 26).

  • Page 38: Pci Riser Cage

    Remove the hard drive backplane. To replace the component, reverse the removal procedure. PCI riser cage To remove the component: CAUTION: For proper cooling do not operate the server without the access panel, baffles, expansion slot covers, or blanks installed. If the server supports hot-plug components, minimize the amount of time the access panel is open.

  • Page 39: Air Baffle

    To replace the component, reverse the removal procedure. Air baffle To remove the component: CAUTION: For proper cooling do not operate the server without the access panel, baffles, expansion slot covers, or blanks installed. If the server supports hot-plug components, minimize the amount of time the access panel is open.

  • Page 40: Expansion Slot Covers

    Remove the air baffle ("Air baffle" on page 39). Remove the fan blanks. Remove the fans ("Hot-plug fan" on page 36). Remove the fan cage. To replace the component, reverse the removal steps and press down on the top of each fan to be sure it is seated properly.
  • Page 41 To remove slot cover 1 or 4, push in on the retainer to release it, and then slide out the cover. To remove slot covers 2 and 3, lift up on the latch, remove the latch, and then remove the cover. Removal and replacement procedures 41...

  • Page 42: Expansion Boards

    To remove slot covers 5 and 6, push down on the latch, rotate the latch down, and then remove the cover. Expansion boards Half-length expansion board To remove the component: Power down the server (on page 26). Extend the server from the rack (on page 25). Remove the access panel ("Access panel"...

  • Page 43: Full-Length Expansion Board

    Remove the expansion board. To replace the component, reverse the removal procedure. Full-length expansion board To remove the component: Power down the server (on page 26). Extend the server from the rack (on page 25). Remove the access panel ("Access panel"...

  • Page 44: Battery-Backed Write Cache Procedures

    To replace the component, reverse the removal procedure. Battery-backed write cache procedures Two types of procedures are provided for the BBWC option: • Removal and replacement of failed components: Removing the cache module (on page 44) Removing the battery pack •...

  • Page 45: Removing The Battery Pack

    Set up a recovery server station using an identical server model. Do not install any internal drives or BBWC in this server. (HP recommends this option.) Find a server that has enough empty drive bays to accommodate all the drives from the failed server and that meets all the other requirements for drive and array migration.

  • Page 46: Heatsink

    Perform one of the following: If the array controller has failed, remove the cache module ("Removing the cache module" on page 44) and battery pack from the failed array controller, and install the cache module and battery pack on an array controller in the recovery server. If the server has failed, remove the controller ("Half-length expansion board"...
  • Page 47 Apply all the grease to the top of the processor in one of the following patterns to ensure even distribution: Install the heatsink. Removal and replacement procedures 47...

  • Page 48: Power Supply Cage Assembly

    Close and lock the heatsink retaining latches. Install the air baffle. Install the PCI riser cage ("PCI riser cage" on page 38). Install the access panel ("Access panel" on page 30). Install the server into the rack. Power up the server. Power supply cage assembly To remove the component: Power down the server (on page 26).

  • Page 49: Processor

    Remove the power supply cage assembly. To replace the component, reverse the removal procedure. Processor CAUTION: To avoid damage to the processor and system board, only authorized personnel should attempt to replace or install the processor in this server. CAUTION: To prevent possible server malfunction and damage to the equipment, multiprocessor configurations must contain processors with the same part number.
  • Page 50 Open the processor retaining latch and the processor socket retaining bracket. Using your fingers, remove the failed processor. To replace a processor: CAUTION: The pins on the processor socket are very fragile. Any damage to them may require replacing the system board. CAUTION: Failure to completely open the processor locking lever prevents the processor from seating during installation, leading to hardware damage.
  • Page 51 If the processor has separated from the installation tool, carefully re-insert the processor in the tool. Align the processor installation tool with the socket and install the processor. CAUTION: The processor is designed to fit one way into the socket. Use the alignment guides on the processor and socket to properly align the processor with the socket.
  • Page 52 Press down firmly until the processor installation tool clicks and separates from the processor, and then remove the processor installation tool. Close the processor retaining bracket and the processor retaining latch. Clean the old thermal grease from the heatsink with the alcohol swab. Allow the alcohol to evaporate before continuing.

  • Page 53: Dimms

    Apply all the grease to the top of the processor in one of the following patterns to ensure even distribution: Install the heatsink. Close and lock the heatsink retaining latches. Install the air baffle. Install the PCI riser cage ("PCI riser cage"...

  • Page 54: Memory Configurations

    Remove the DIMM. To replace the component, reverse the removal procedure. Memory configurations This server supports 2 GB to 128 GB of Advanced ECC system memory using 1-GB, 2-GB, 4-GB, and 8-GB registered DDR-2 DIMMS across 16 DIMM slots. Depending on the quantity and speed of DIMMs populated, memory bus speeds can be 533-MHz, 667-MHz, or 800-MHz.
  • Page 55 • DIMM pairs in a memory bank must have identical HP DIMM part numbers. • Only HP DIMM part numbers listed in the QuickSpecs for this server should be used in this server. DIMM population order Bank A Bank B...

  • Page 56: System Battery

    System battery If the server no longer automatically displays the correct date and time, you may need to replace the battery that provides power to the real-time clock. WARNING: The computer contains an internal lithium manganese dioxide, a vanadium pentoxide, or an alkaline battery pack. A risk of fire and burns exists if the battery pack is not properly handled.
  • Page 57 Remove all power supplies ("Hot-plug power supply" on page 28). Extend or remove the server from the rack ("Remove the server from the rack" on page 27, "Extend the server from the rack" on page 25). Remove the access panel ("Access panel"...
  • Page 58 Using your fingers, remove the failed processor. CAUTION: To avoid damage to the system board: Do not touch the socket contacts. • Always install the processor socket cover after removing the processor from the socket. • • Do not tilt or slide the processor when removing the processor from the socket. CAUTION: To avoid damage to the processor: •...
  • Page 59 To migrate the processor to the spare system board: Install the spare system board. CAUTION: The pins on the processor socket are very fragile. Any damage to them may require replacing the system board. Prepare the processor socket on the spare system board: Remove the processor socket protective cover.
  • Page 60 CAUTION: Always install the processor parallel to the system board to avoid damage to the pins. Close the processor retaining latch and the processor socket retaining bracket. Clean the old thermal grease from the heatsink and the top of the processor with the alcohol swab. Allow the alcohol to evaporate before continuing.
  • Page 61 Apply all the grease to the top of the processor in one of the following patterns to ensure even distribution: Install the heatsink ("Heatsink" on page 46). Install all components removed from the failed system board. Install the access panel ("Access panel"...

  • Page 62: Cabling

    Cabling SAS hard drive cabling Battery cabling for BBWC Cabling 62...

  • Page 63: Diagnostic Tools

    ASR increases server availability by restarting the server within a specified time after a system hang or shutdown. At the same time, the HP SIM console notifies you by sending a message to a designated pager number that ASR has restarted the system. You can disable ASR from the HP SIM console or through RBSU.

  • Page 64: Integrated Management Log

    Diagnose iLO 2 using HP SIM through a web browser and SNMP alerting. For more information about iLO 2 features (which may require an iLO Advanced Pack or iLO Advanced for BladeSystem license), see the iLO 2 documentation on the Documentation CD or on the HP website (http://www.hp.com/servers/lights-out).

  • Page 65: Hp Proliant Essentials Rapid Deployment Pack

    It enables you to perform imaging or scripting functions and maintain software images. For more information about the RDP, refer to the HP ProLiant Essentials Rapid Deployment Pack CD or refer to the HP website (http://www.hp.com/servers/rdp).

  • Page 66: Rompaq Utility

    To download the tool and for more information, see the HP website (http://www.hp.com/support). HP Insight Diagnostics HP Insight Diagnostics is a proactive server management tool, available in both offline and online versions, that provides diagnostics and troubleshooting capabilities to assist IT administrators who verify server installations, troubleshoot problems, and perform repair validation.

  • Page 67: Redundant Rom Support

    Redundant ROM support The server enables you to upgrade or configure the ROM safely with redundant ROM support. The server has a 4-MB ROM that acts as two, separate 2-MB ROMs. In the standard implementation, one side of the ROM contains the current ROM program version, while the other side of the ROM contains a backup version.

  • Page 68: Component Identification

    Component identification Front panel components Item Description Serial number label Systems Insight Display Video connector USB connectors (2) Hard drive bays SATA optical drive bay Quick release levers (2) CAUTION: For proper cooling do not operate the server without the access panel, baffles, expansion slot covers, or blanks installed.

  • Page 69: Systems Insight Display Leds

    Item Description Status Health LED Green = Normal Flashing amber = System degraded. To identify a component in a degraded state, see "Systems Insight Display LEDs (on page 69)." Flashing red = System critical. To identify a component in a critical state, see "Systems Insight Display LEDs (on page 69)."...

  • Page 70: Rear Panel Components

    Systems Insight Display Internal health Status LED and color LED color One or more of the following conditions may exist: Processor (amber) • Processor in socket X has failed. • Processor X is not installed in the socket. • Processor X is unsupported. •...

  • Page 71: Rear Panel Leds And Buttons

    Item Description Color PCI slot 5 — PCI slot 6 — PCI slot 4 — PCI slot 2 — PCI slot 3 — PCI slot 1 — Power supply 2 — Power supply 2 connector — Power supply 1 — Power supply 1 connector —...

  • Page 72: Non-Hot-Plug Pci Riser Board Slot Definitions

    FL/FH denotes full-length, full-height. HL/FH denotes half-length, full-height. LP denotes low profile. • The PCIe x16 riser supports a maximum power of 225W with an HP power cable. This cable must be used for PCIe card wattages greater than 75W.

  • Page 73: System Board

    System board System board components Item Description Processor 1 DIMM slots Primary SAS power connector Secondary SAS power connector Front I/O connector SATA optical drive connector USB connector System battery connector TPM connector NMI jumper System maintenance switch Power supply backplane connector Processor 1 socket Primary riser connector Secondary riser connector...

  • Page 74: System Board Switches

    To force the OS to invoke the NMI handler and generate a crash dump log, the administrator can do any of the following: • Short the NMI jumper pins • Press the NMI switch • Use the iLO Virtual NMI feature For additional information, see the whitepaper on the HP website (http://h20000.www2.hp.com/bc/docs/support/SupportManual/c00797875/c00797875.pdf). Component identification 74...

  • Page 75: Dimm Slots

    DIMM slots DIMM slots are identified by the numbers 1 through 16 and paired banks are identified by the letters A through H. Hard drive numbering SAS and SATA hard drive LEDs Component identification 75...

  • Page 76: Sas And Sata Hard Drive Led Combinations

    Item Description Fault/UID LED (amber/blue) Online LED (green) SAS and SATA hard drive LED combinations Online/activity Fault/UID LED Interpretation LED (green) (amber/blue) On, off, or flashing Alternating amber The drive has failed, or a predictive failure alert has been received and blue for this drive;...

  • Page 77: Battery Pack Leds

    Status On = AC power is connected. Off = AC power is disconnected. Missing = Riser is not installed and power might be connected. Battery pack LEDs Item ID Color Description Green System Power LED. This LED glows steadily when the system is powered up and 12 V system power is available.

  • Page 78: Hot-Plug Fans

    A fully-charged battery can normally preserve data for at least two days. The battery lifetime also depends on the cache module size. For further information, refer to the controller QuickSpecs on the HP website (http://www.hp.com). Double blink, then The cache microcontroller is waiting for the host controller to —...
  • Page 79 For more information, see "Hot-plug fan operation ("Hot-plug fan" on page 36)." Component identification 79...

  • Page 80: Specifications

    Specifications Environmental specifications Specification Value Temperature range* 10°C to 35°C (50°F to 95°F) Operating -30°C to 50°C (-22°F to 122°F) Shipping -30°C to 60°C (-22°F to 140°F) Storage 28°C (82.4°F) Maximum wet bulb temperature Relative humidity (noncondensing)** 10% to 90% Operating 5% to 95% Non-operating...

  • Page 81: Hot-Plug Power Supply Calculations

    System input requirements information is based on measurements with hardware available at the time of publishing this document. For updated information, visit the HP website (http://www.hp.com/servers/powercalculator). Hot-plug power supply calculations For hot-plug power supply specifications and calculators to determine electrical and heat loading for the server, refer to the HP Enterprise Configurator website (http://h30099.www3.hp.com/configurator/).

  • Page 82: Dvd-Rom Drive Specifications

    Specification Value 53.5° ± 1.5° Divergence angle 0.14 mW Output power Operating conditions 5°C to 55°C (41°F to 131°F) Temperature 10% to 80% Humidity DVD-ROM drive specifications Specification Value DVD (single and double layer), DVD-5, DVD-9, DVD-10, DVD-R, CD-ROM Mode 1 Disk formats &...

  • Page 83: Sas And Sata Hard Drive Specifications

    Specification Value 5°C to 55°C (41°F to 131°F) Temperature 10% to 80% Humidity SAS and SATA hard drive specifications Item 36-GB SAS drive 72-GB SAS drive 60-GB SATA drive 36,420 MB 73,408 MB 60,022 MB Capacity 15 mm 15 mm 9 mm Height Serial ATA...

  • Page 84: Acronyms And Abbreviations

    Acronyms and abbreviations ABEND abnormal end Automatic Server Recovery BBWC battery-backed write cache double data rate Integrated Lights-Out Integrated Management Log non-maskable interrupt NVRAM non-volatile memory ORCA Option ROM Configuration for Arrays PCIe peripheral component interconnect express PCI-X peripheral component interconnect extended POST Power-On Self Test Acronyms and abbreviations 84...
  • Page 85 RBSU ROM-Based Setup Utility Rapid Deployment Pack serial attached SCSI SATA serial ATA trusted platform module unit identification universal serial bus Acronyms and abbreviations 85...

  • Page 86: Documentation Feedback

    Documentation feedback HP is committed to providing documentation that meets your needs. To help us improve the documentation, send any errors, suggestions, or comments to Documentation Feedback (mailto:docsfeedback@hp.com). Include the document title and part number, version number, or the URL when submitting your feedback.

  • Page 87: Index

    HP Insight Diagnostics 66 creating a disk image 65 HP ProLiant Essentials Foundation Pack 63 CSR (customer self repair) 5 HP ProLiant Essentials Rapid Deployment Pack 65 customer self repair (CSR) 5 HP Systems Insight Manager overview 63 deployment software 65...
  • Page 88 iLO 2 connector 70 power supply backplane 35 IML (Integrated Management Log) 64 power supply blank 31 Insight Diagnostics 66 power supply cage assembly 48 Integrated Lights-Out (iLO) 64 power supply LEDs 71 Integrated Management Log (IML) 64 powering down 26 preparation procedures 25 internal health LED 69, 76 processors 49...
  • Page 89 telco racks 25, 27 tools 63 TPM (Trusted Platform Module) 30 troubleshooting 63 Trusted Platform Module (TPM) 30 UID LED 68, 71, 74 USB connectors 68, 70 utilities 63 utilities, deployment 65 video connector 68, 70 warnings 24 Index 89...

Table of Contents