Table of Contents
Advertisement
TAPE
Use padded hand truck to protect
refrigerator finish. LEAVE TAPE
ON DOORS until refrigerator is in
its final location. TRUCK FROM
SIDE ONLY. Avoid overtightening
strap to prevent damaging doors.
• APPLIANCE POLISH WAX IS RECOMMENDED FOR REMOVING TAPE RESIDUE AND HAND PRINTS FROM REFRIGERATOR EXTERIOR.
• REMOVE ALL TAPE AND OTHER PACKAGING MATERIAL FROM REFRIGERATOR INTERIOR. DO NOT REMOVE SERIAL PLATE.
• REMOVE PROTECTIVE FILM ON TEMPERATURE CONTROL PANEL.
Removing Doors
Doors should be in closed position. Near lower hinge
WIRE
on freezer side, squeeze collar on water line and pull
HARNESS
tubing from coupling. Also, disconnect wiring harness.
COLLARS
Pull water line and harness through lower rail.
HINGE
Remove top hinge covers to access hinges. Remove
COVER
NOTICE
hinges using a Torx T-20.
Carefully rotate door through 90°. Guiding water line
and wiring harness, lift door straight up. Avoid side
loading the bottom hinges. Place doors on a protective
surface. Avoid pinching the water tube and wire
DOOR
90
harness at the bottom of the door.
HINGE
PIN
CAUTION: Do NOT allow the connector to contact the floor. Hard contact can damage the connector.
PREFERRED
METHOD
The power cord of this appliance is equipped with a three-prong (grounding) plug that mates with a standard three-prong (grounding) wall receptacle to minimize the
risk of electric shock hazard from this appliance. The customer should have the wall receptacle and circuit checked by a qualified electrician to make sure the receptacle
is properly grounded.
Where a standard two-prong wall receptacle is encountered, it is the personal responsibility and obligation of the customer to have it replaced with a properly grounded
three-prong wall receptacle.
MAKE SURE PROPER
GROUND EXISTS
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE THIRD (GROUND) PRONG FROM THE POWER CORD.
BEFORE USE
USAGE SITUATIONS WHERE THE APPLIANCE'S POWER CORD WILL BE DISCONNECTED INFREQUENTLY
Because of potential safety hazards under certain conditions, we strongly recommend against the use of an adapter plug. However, if you still elect to use an adapter,
TEMPORARY METHOD
where local codes permit, a TEMPORARY CONNECTION may be made to a properly grounded two-prong wall receptacle by the use of a UL listed adapter which is
(Adapter plugs not
available at most hardware stores. The larger slot of the adapter must be aligned to provide proper polarity in the connection of the power cord.
permitted in Canada)
CAUTION: Attaching the adapter ground terminal to the wall receptacle cover screw does not ground the appliance unless the cover screw is metal, and not insulated,
and the wall receptacle is grounded through the house wiring. The customer should have the circuit checked by a qualified electrician to make sure the receptacle is
properly grounded. When disconnecting the power cord from the adapter, always hold the adapter with one hand. If this is not done, the adapter ground terminal is very
likely to break with repeated use. Should this happen, DO NOT USE the appliance until a proper ground has again been established.
USAGE SITUATIONS WHERE THE APPLIANCE'S POWER CORD WILL BE DISCONNECTED FREQUENTLY
ENSURE PROPER
Do not use an adapter plug in these situations because frequent disconnecting of the power cord places undue strain on the adapter and leads to eventual failure of the
GROUND AND
adapter ground terminal. The customer should have the two-prong wall receptacle replaced with a three-prong (grounding) receptacle by a qualified electrician before
FIRM CONNECTION
using the appliance.
BEFORE USE
Installation
REMOVE ALL CLEAR PROTECTIVE
TAPE FROM TRIMS, then move unit
into position. If entrance is less
than 38" wide, remove doors prior
to installation and reinstall doors
according to procedure below.
IMPORTANT: PLEASE READ CAREFULLY
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED.
– 3 –
ROLLER HEIGHT
ADJUSTMENT
DOOR HEIGHT
ADJUSTMENT
Connect water lines and power cord.
ADJUST FRONT ROLLERS so the
refrigerator is solid on floor and
doors close easily. MAKE SURE
DOORS ARE EVEN AT TOP.
Re-installing Doors
With Doors 90° open, place doors on bottom hinge.
Carefully rotate doors to closed position. Avoid side
loading the bottom hinges.
Reinstall top hinges and tighten screws firmly.
Reinstall hinge cover. If doors are not level, adjust
" open ended wrench.
bottom right hinges with a
7
⁄
16
Insert water tubing back into coupling. It is completely
connected when the mark on the tubing is no longer
visible. Reconnect wire harness. Turn on water supply.
TEMPERATURE CONTROLS ARE
PRESET IN THE FACTORY FOR
RECOMMENDED SETTINGS.
90
DOOR
HINGE
PIN
HINGE
COVER
WIRE
HARNESS
COLLARS
- Quick Links:
- Diagnostic Tests (Table 2)
- Self Diagnostics
Hide quick links:
Advertisement
Chapters
Table of Contents
