Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Major 601SL
Summary of Contents for Major 601SL
- Page 1 Operator Manual & Parts List MAJOR GRASS SLASHERS & JUNGLE BUSTER...
- Page 2 Major reserves the right to modify the machinery and the technical data contained within the manual without prior notice. Further to this, Major assumes no liability for any damages which may result from the use of the information contained within this manual.
-
Page 3: Table Of Contents
Driving safely on public roads Operating the Machine Inspections before Use Key to Main Parts Starting Regulations Hitching to the tractor Operating the Machine/Mowing Maintenance Greasing schedule Trouble Shooting Spare Parts 601SL Grass Slasher 605SL Grass Slasher Jungle Buster (JB) 609SL Grass Slasher Gearboxes... - Page 4 EN ISO 13857 - Safety of machinery: Safety distances to prevent hazard zones being reached by upper and lower limbs. I certify on behalf of Major Equipment Int. Ltd., that this machine when properly installed and operated correctly, complies with all the essential Health & Safety requirements of all legislation referred to above.
-
Page 5: Thank You
Machine Serial Numbers If you need to contact MAJOR or your MAJOR dealer for information on servicing or spare parts, always provide the product model and serial numbers. Model and Serial number can be found on the Serial Plate located on the machine. -
Page 6: Machine Safety Labels
Product Specifications Model PTO input Cutting width Cutting Range No. of blades Power requirements 601SL 540 RPM 1700mm / 5’ 7” 10 - 250mm /1/2” - 10” 30 - 60 HP 605SL 540 RPM 1830mm/ 6’ 10 - 250mm /1/2” - 10”... - Page 7 Slips and falls often result from: 1. Slippery footing on the ground 2. Cluttered steps and work platforms. The potential for slips and falls can be greatly reduced by using good judgement and practicing good housekeeping on and around equipment. www.major-equipment.com...
-
Page 8: Operating Safely
Operating Safely This MAJOR machine is designed to operate at a PTO rate which is stated in the Product Specifications part of this booklet. Ensure tractor PTO output is set at a correct RPM rate. This MAJOR machine must only be used for purposes outlined in the Intended Use section of this booklet. -
Page 9: Pto Shaft Safety
4. It is mandatory to read all the safety requirements and the operator’s manual of the machine. 5. If you are not sure how to use the machine, please contact the manufacturer or the dealer. www.major-equipment.com... -
Page 10: Operating The Machine
Operating the Machine Inspections before Use Always disengage PTO, Switch off tractor engine and engage the parking brake before making adjustments to the machine. 1. With the whole machine as level as possible, check the oil level in the gearboxes. Top up as required with SAE EP90 gear oil through the oil filler plug indicated. -
Page 11: Hitching To The Tractor
Operating the Machine/Mowing The MAJOR Pasture Topper is designed to operate at a max 540 rpm (1000 RPM Jungle Buster. Always operate on level ground when hitching / unhitching the implement. This will prevent dangerous movement. Never allow anyone to stand between the tractor and the pasture topper. -
Page 12: Trouble Shooting
Trouble Shooting FAULT POSSIBLE CAUSE REMEDY Irregular cut Worn or broken blades Sharpen or replace blades Loose parts Check all bolts are fully tightened. Noisy machine Insufficient oil in gearbox. Check oil level and top up as necessary. Incorrect PTO R.P.M. rate. Check PTO R.P.M. -
Page 13: 601Sl Grass Slasher
Spare Parts - Slashers Use Genuine Parts For best results you should always choose geniune parts for your machines. MAJOR spare parts are identical to those used on our machines during assembly. They have been developed by our R&D department and tested thoroughly to meet high quality standards. -
Page 14: 605Sl Grass Slasher
605SL Grass Slasher Se nedenfor Item Part No Description Item Part No Description SL61-FG FRONT GUARD 14 M12x30SZP M12x30 SET BOLT SL65-BLD 605 BLADE ASSY (STD) 15 M12x35BZP M12x35 BOLT SL65-BOD 605 SLASHER BODY 16 M20 M20 NYLOC NUT SL65RG REAR GUARD 17 M20x110BZP M20x110 BOLT... -
Page 15: Jungle Buster (Jb)
Jungle Buster (JB) Item Part No Description Item Part No Description 16WT-BBA JB WING BLADE ASSY (Front Mt) 16 M12 M12 NYLOC NUT 16WT-WBB JB WING BLADE ASSY (Rear Mt) 17 M12x30SZP M12x30 SET BOLT FS18-B01 FORESTRY 180 BODY 18 M16 M16 NYLOC NUT FS18-FG01 FRONT FLAP GUARD... -
Page 16: 609Sl Grass Slasher
609SL Grass Slasher BEFORE HR16350 Item Part No. Description SL609-BGA SLASHER BODY WELDMENT SL609-LMW SLASHER LINKAGE WELDMENT SL609-LMW-H HANDED LINKAGE WELDMENT SL69-BLD 609 BLADE ASSY (STD) SL69-SKD SKID (OFFSET) 3546 LINCH PIN DIA 9.5 5/8F 5/8" FINE NYLOC NUT 58x214FBZP 5/8"x2 1/4"... - Page 17 609SL Grass Slasher AFTER HR16350 Item Part No. Description CAT 2 PIN DIA 25.4x110mm SL69-BLD 609 BLADE ASSY (STD) AN099/10 LINCH PIN DIA 9.5 STANDARD A-FRAME DSR-1-2 1/2" RATED 'D' SHACKLE MJ40L (347800) 6 SPLINE 'L' BOX RATIO 1.47 DSR-5-8 5/8"...
- Page 18 609 Slasher Blade Assembly Item Part No. Description 1/2F 1/2" FINE NYLOC NUT 12x212FBZP 1/2"x2 1/2" FINE BOLT 6SL-NB BLADE BACK (925 CTR) 9GT-USS UNDER SOLE SKID BLD-51535 609 SLASHER BLADE DSW45 DISC SPRING 45x22.4x2.5 FW12 12" FLAT WASHER M20 NYLOC NUT 10 M20x60BZP M20x60 BOLT 11 6SL-BB...
-
Page 19: Gearboxes
Gearboxes LF149/B (9.149.036.00) Gearbox Breakdown Item Part No Description Item Part No Description 0.149.0301.00 CASING 0.149.5000.00 GEAR Z20 M6.25 8.0.9.00129 BEARING 30307 8.0.9.00469 BEARING 30210 0.244.7500.00 SHIM KIT 40.3x51.5 8.7.1.00315 (358010) DOUBLE LIP SEAL 35X80X10 0.259.7525.00 SHIM 35.3x2.5 0.149.2001.00 SHAFT 1”3/8 Z6 8.7.0.00790 80X10 85200030... - Page 20 10 LF135/9 8.0.1.00871 Bearing 6208 26 0.248.7500.00 0.2.4.8750000 Shim 11 LF135/1 8.2.2.00515 Castle Nut 27 85200131 8.5.2.00131 Circlip 12 LF135/2 8.3.2.00409 Washer 13 LF135/19 8.4.1.00993 14 M10x20SZP 8.11.00054 Bolt 15 LF135/6 8.5.1.00030 Snap Ring 16 LF135/3 8.5.3.00955 Snap Ring www.major-equipment.com...
- Page 21 Snap Ring (72x75x2.5 , For Holes) 22 8.5.3.00955 Snap Ring SB 81 (81x82.8x2) 7 0.248.7500.00 Shim Kit (60.3x71.7) 23 0.205.7100.00 “Major” Name Plate 8 8.5.1.00680 Snap Ring (40x37.5x2.5 , For Shafts) 24 8.4.7.00823 Cotter Pin (4x40) 9 0.289.7102.02 Castle Nut (M20X1) 25 0.347.1300.00...
- Page 22 Warranty: This machine is guaranteed for 12 months. No warranty is given where the machine is being used as a hire machine. Warranty is against faulty workmanship or parts, with the exception of components not of MAJOR’S manufacture or design, i.e.
- Page 23 HEAD OFFICE UK OFFICE Netherlands & Germany OFFICE Major Equipment Intl Ltd Major Equipment Ltd Major Equipment Intl Ltd Ballyhaunis, Co Mayo Major Ind. Estate, Heysham, Postbus 29, NL-7700 AA Ireland Lancs, LA3 3JJ, UK Dedemsvaart, Nederland Tel: +353 (0) 9496 30572...