Related Manuals for CAEL 4PG8000
Summary of Contents for CAEL 4PG8000
- Page 1 Capital Automotive Equipment Model:4PG8000 Four Post Car parking Lift 4PG8000 manual operation and manual lock release Installation and Operation Manual 4PG8000 with optional casters...
- Page 2 Capital Automotive Equipment Model:4PG8000 IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS PLEASE READ THE ENTIRE CONTENTS OF THIS MANUAL PRIOR TOINSTALLATION AND OPERATION. BY PROCEEDING WITH LIFT INSTALLATION AND OPERATION YOU AGREE THAT YOU FULLY UNDERSTAND AND COMPREHEND THE FULL CONTENTS OF THIS MANUAL. FORWARD THIS MANUAL TO ALL OPERATORS.
-
Page 3: Chapter 1 Packing, Transport And Storage
Capital Automotive Equipment Model:4PG8000 Chapter 1 Packing, transport and storage ALL PACKING, LIFTING, HANDLING, TRANSPORT AND UNPACKING ORERATIONS ARE TO BE PERFORMED EXCLUSIVELY BY EXPERT PERSONNEL WITH KNOWLEDGE OF THE LIFT AND THE CONTENTS OF THIS MANUL. 1.1Package The dimension of package, please see below, and the package weight is 910kg 1.2 Transport... - Page 4 Capital Automotive Equipment Model:4PG8000 1.3 Storage -The machine equipment should be stocked in the warehouse, if stocked outside should do the disposal well of waterproof. -Use box truck in the process of transport, use container storage when shipping. -The control box should be placed perpendicularly during the transport; and prevent other goods from extrusion.
-
Page 5: Chapter 2 Description Of The Machine
Capital Automotive Equipment Model:4PG8000 Chapter 2 Description of the machine 2.1 Introduction The 4 post parking lifts are products of our research and development division, its special features include a lifting capacity of 8000 lbs (3600kg). 2.2 Intend use This Four post lift can lift various vehicles which weight is less than 8000 lbs (3600kg). And it is suitable for vehicle test, repair, maintenance and care. -
Page 6: Chapter 3 Safety Caution
Capital Automotive Equipment Model:4PG8000 Chapter 3 Safety caution Read this chapter carefully and completely because it contains important information for the safety of the operator and the person in charge of maintenance. The lift has been designed and built for lifting vehicles and making them stand above level in a closed area any other use is forbidden. -
Page 7: Chapter 4 Installation
Capital Automotive Equipment Model:4PG8000 Chapter 4 Installation Only skilled technicians, appointed by the manufacturer, or by authorized dealers, must be allowed to carry out installation. Serious damage to people and to the lift can be caused if installations are made by unskilled personnel. - Page 8 Capital Automotive Equipment Model:4PG8000 4. Re-check all the dimensions to ensure that each column of the base shape and position consistent with the chalk line. 5. Firstly, place cylinder in the positioning hole in the column bottom, then after fixing slider to slide, push the slide to bottom of the column from top.
-
Page 9: Chapter 5 Adjustment
Capital Automotive Equipment Model:4PG8000 and the power unit mounting plate on the Power Side post, using four M8 hex head bolts and nuts supplied. M8 x1.25 x 35mm hex head bolts, M8 flat washers and M8 Nylock nuts 11. According to the hydraulic layout diagram, connect the oil pipes. - Page 10 Capital Automotive Equipment Model:4PG8000 5.3 Synchronization adjustment • Repeat to lift and lower the lift several times, to ensure the tensile force and balance of4 steel cables. If not, adjust the cable nut. 5.4 Loading test To check whether hydraulic system works normally when loading heavy weight.
-
Page 11: Chapter 6 Operation Instruction
Capital Automotive Equipment Model:4PG8000 Chapter 6 Operation instruction Never operate the lift with any person or equipment below. Never exceed the rate lifting capacity. Always ensure that the mechanical safeties are engaged before any attempt is made to work on or near the vehicle. -
Page 12: Weekly Maintenance
Capital Automotive Equipment Model:4PG8000 Raise the lift off the safety locks by pushing the UP button on the power unit. make sure you raise the lift by at least two inches to allow adequate clearance for the locks to clear. -
Page 13: Chapter 7 Maintenance
Capital Automotive Equipment Model:4PG8000 Chapter 7 Maintenance Cut off the power supply before servicing the lift. The maintenance intervals indicated below apply to average workshop use. The lift should be inspected more frequently for severe use applications. 7.1 Maintenance Schedule Establish a periodic preventive maintenance procedure to ensure trouble free operation and long service life. - Page 14 Capital Automotive Equipment Model:4PG8000 The slide tracks inside the columns should be greased every six months (or more frequently in case of noise generation) Slide Tracks The slide tracks inside the columns should be greased every six months (or more frequently in case of noise generation).
-
Page 15: Chapter 8 Trouble Shooting
Capital Automotive Equipment Model:4PG8000 Every six months check the nuts of all anchor bolts for correct installation torque Tinst. Retighten them as required. Installation Torque Tinst 4PG8000 80 Nm 7.4 Cleaning Do not use high pressure / steam jet cleaners or caustic cleaning agents. -
Page 16: Chapter 9 Disposal Of Used Oil
Capital Automotive Equipment Model:4PG8000 The suction tube or pump filter is dirty. Check and clean if needed. Presence of air in the hydraulic system Bleed the hydraulic system Check the pump and replace if The pump is faulty needed. The lifting capacity is not...