hit counter script
Siemens SIMATIC HMI 177 Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Siemens Manuals
  4. Control Panel
  5. SIMATIC HMI 177
  6. Operating instructions manual

Siemens SIMATIC HMI 177 Operating Instructions Manual

Hmi device mobile panel
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
SIMATIC HMI HMI device Mobile Panel 177 (WinCC flexible)
SIMATIC HMI
HMI device
Mobile Panel 177 (WinCC flexible)
Operating Instructions (Compact)
Edition 07/2005
A5E00457453-01
Foreword
______________
Overview
Safety instructions and
______________
general notes
______________
Planning Use
______________
Mounting and Connection
Operator elements and
______________
displays
______________
Specifications
______________
Appendix
1
2
3
4
5
6
A

Advertisement

Table of Contents
loading

Related Manuals for Siemens SIMATIC HMI 177

Summary of Contents for Siemens SIMATIC HMI 177

  • Page 1 Foreword SIMATIC HMI HMI device Mobile Panel 177 (WinCC flexible) ______________ Overview Safety instructions and ______________ general notes SIMATIC HMI ______________ Planning Use HMI device Mobile Panel 177 (WinCC flexible) ______________ Mounting and Connection Operator elements and ______________ displays Operating Instructions (Compact) ______________ Specifications ______________...
  • Page 2 Trademarks All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
  • Page 3 Detailed information on Mobile Panel 177 can be found in the "Mobile Panel 177" operating instructions. The "Mobile Panel 177" operating instructions and further documentation are available for download on the internet under "http://www.siemens.com/automation/service". Mobile Panel 177 (WinCC flexible) Operating Instructions (Compact), Edition 07/2005...
  • Page 4 Foreword Mobile Panel 177 (WinCC flexible) Operating Instructions (Compact), Edition 07/2005...

  • Page 5: Table Of Contents

    Table of contents Foreword ..............................i Overview..............................1-1 Design ............................1-1 Mobile Panel 177 ........................1-2 Connecting cables ........................1-4 Terminal box ..........................1-6 Wall holder ..........................1-9 Safety instructions and general notes ..................... 2-1 Operating safety......................... 2-1 Risk analysis ..........................2-2 Planning Use ............................
  • Page 6 Table of contents 5.1.4.2 STOP button on Terminal Box Plus ................... 5-7 5.1.4.3 STOP button on Terminal Box Basic ..................5-8 5.1.5 Hand wheel ..........................5-10 5.1.6 Key-operated switch......................... 5-11 5.1.7 Illuminated pushbutton ......................5-12 Terminal Box PN ........................5-13 Specifications ............................

  • Page 7: Overview

    Overview Design Design The following figure shows the Mobile Panel 177 with a terminal box. For stationary operation, the Mobile Panel 177 can be securely placed in a wall holder (not shown). Figure 1-1 Mobile Panel design, example Mobile Panel 177 DP ①...

  • Page 8: Mobile Panel 177

    Overview 1.2 Mobile Panel 177 Mobile Panel 177 Introduction The Mobile Panel 177 comes equipped in the following three ways: • With enabling switches • With enabling switches and STOP button • With enabling switches, STOP button, handwheel, key-operated switch, and illuminated pushbutton This variant is shown in the following illustrations.
  • Page 9 Overview 1.2 Mobile Panel 177 Figure 1-3 Side view ① Fall protection for the STOP pushbutton ② STOP button, optional ③ Enabling switches, located on both sides of the Mobile Panel 177 ④ Grip Figure 1-4 Rear view with opened terminal compartment on Mobile Panel 177 DP ①...

  • Page 10: Connecting Cables

    For connecting the Mobile Panel 177 PN to the terminal box PN. The connecting cables are available in different lengths. Further information can be found in the Siemens ST 80 catalog. Mobile Panel 177 (WinCC flexible) Operating Instructions (Compact), Edition 07/2005...
  • Page 11 Overview 1.3 Connecting cables Design of the connecting cable Figure 1-6 Connecting cable DP Figure 1-7 Connecting cable PN ① Metallic push-pull circular connector ② Strain relief and kink protection for connecting cable ③ RJ45 plug ④ Plug connector Connections on the Mobile Panel 177 DP •...

  • Page 12: Terminal Box

    Overview 1.4 Terminal box Terminal box Design Figure 1-8 Terminal Box DP ① Screwed joint for process data line ② Screwed joint for power supply cable and shield ③ Screwed joint for cable with supplementary Stop and enabling switch signals and for PLC- accompanying signals ④...
  • Page 13 Overview 1.4 Terminal box Figure 1-9 Terminal Box PN ① Screwed joint for process data line ② LED displays ③ Screwed joint for power supply cable and shield ④ Screwed joint for cable with supplementary Stop and enabling switch signals and for PLC- accompanying signals ⑤...
  • Page 14 Overview 1.4 Terminal box Note Recovery time Wait for approx. one second after you have removed the connecting cable from the terminal box before you plug the connecting cable back in. After power failures of less than one second the connecting cable has to be disconnected. Division of the system into zones You can divide a system into several zones or functional areas by using several terminal boxes, whereby the safety functions can also be set up to be zone-specific.

  • Page 15: Wall Holder

    Overview 1.5 Wall holder Wall holder Function The wall holder is used to securely mount the Mobile Panel 177 for stationary operation. Figure 1-10 Wall holder ① Hook for the grip on the HMI device ② Screw-on hole Mobile Panel 177 (WinCC flexible) Operating Instructions (Compact), Edition 07/2005...
  • Page 16 Overview 1.5 Wall holder Mobile Panel 177 (WinCC flexible) 1-10 Operating Instructions (Compact), Edition 07/2005...

  • Page 17: Safety Instructions And General Notes

    Safety instructions and general notes Operating safety Standards The HMI device complies with the following standards: • EN 60204-1 Safety of Machinery – Electrical Equipment of Machines • EN 61131-1 and EN 61131-2 Programmable Logic Controllers • The HMI device was tested for EMC in accordance with the following standards: –...

  • Page 18: Risk Analysis

    Safety instructions and general notes 2.2 Risk analysis Risk analysis Carrying out a risk analysis The following standards must be used to perform the risk analysis: • EN 292, General Machinery Directives • EN 1050 Risk Assessment for Machinery • EN 954-1 Safety of Machinery These considerations lead to a safety category (B, 1, 2, 3, 4) in accordance with EN 954-1 that ultimately dictates how the safety-related aspects of the system to be monitored are to be furnished.

  • Page 19: Planning Use

    Planning Use Mounting positions and type of fixation Mounting position The wall holder is designed for vertical mounting. The terminal box is designed for surface mounting independently of cabinets or control panels. The terminal box is self-ventilated and is approved for all mounting positions. Note that the guaranteed protection rating is only ensured if the connecting cable or the dummy cap is plugged into the terminal box.

  • Page 20: Preparing Mounting

    Planning Use 3.2 Preparing mounting Preparing mounting Selecting the mounting location for the HMI device holder Observe the following points when selecting the mounting location: • Position the wall holder so that the display of the hooked-in HMI device is not exposed to direct sunlight.
  • Page 21 Planning Use 3.2 Preparing mounting The following clearances are required around the Terminal Box DP: The following clearances are required around the Terminal Box PN. Mobile Panel 177 (WinCC flexible) Operating Instructions (Compact), Edition 07/2005...
  • Page 22 Planning Use 3.2 Preparing mounting Mobile Panel 177 (WinCC flexible) Operating Instructions (Compact), Edition 07/2005...

  • Page 23: Mounting And Connection

    Mounting and Connection Mounting the terminal box and wall holder Requirements The following are required for mounting: • Three M5 cylinder head screws for the wall mounting of the HMI device • Four M4 cylinder head screws for the terminal box If the HMI device is to be operated while hooked into the wall holder, ensure that the connecting cable is sufficiently long.
  • Page 24 Mounting and Connection 4.1 Mounting the terminal box and wall holder Procedure – mounting the terminal box Note Length of the connecting cable Take into account the maximum length of the connecting cable when selecting the position for the terminal box. Proceed as follows: 1.

  • Page 25: Connecting The Terminal Box

    Mounting and Connection 4.2 Connecting the terminal box Connecting the terminal box 4.2.1 Opening and closing the terminal box Introduction Please note: Caution Short circuits in the terminal box can impair the function of the Mobile Panel 177. When carrying out work in the opened terminal box ensure that conductive materials, such as cable residues, do not come into contact with electrical circuits.
  • Page 26 Mounting and Connection 4.2 Connecting the terminal box Proceed as follows: 1. Loosen the four screws 2. Put down the screws and cover 3. Put the opened terminal box down securely Protective cover of the Terminal Box PN ① Protective cover Note Protective cover Do not remove the protective cover, because otherwise the electronics of the terminal box...

  • Page 27: Interfaces To The Terminal Box Dp

    Mounting and Connection 4.2 Connecting the terminal box 4.2.2 Interfaces to the Terminal Box DP The following interfaces are available on the terminal box: Figure 4-2 Interfaces to the Terminal Box DP ① Fast connector ② Terminal strip 1 for RS 232, RS 422, RS 485 and power supply ③...

  • Page 28: Interfaces To The Terminal Box Pn

    Mounting and Connection 4.2 Connecting the terminal box 4.2.3 Interfaces to the Terminal Box PN The following interfaces are available on the terminal box: Figure 4-3 Interfaces to the Terminal Box PN ① Fast connector ② Terminal strip 1 for supply voltage ③...

  • Page 29: Setting The Box Id At The Terminal Box

    Mounting and Connection 4.2 Connecting the terminal box 4.2.4 Setting the box ID at the terminal box Introduction You can set a unique box ID for station identification in each terminal box. If configured correspondingly, the box ID can be read out of the HMI device and transmitted to the controller.
  • Page 30 Mounting and Connection 4.2 Connecting the terminal box Example for setting the box ID Figure 4-6 Example for the address "27H" ① Rotary encoding switch for more significant bits ② Rotary encoding switch for less significant bits The figure shows the set address 27H, which is the same as address 39 in decimal format. Procedure Proceed as follows: 1.

  • Page 31: Stripping The Insulation Of Cables

    Figure 4-8 Stripping the PROFINET cable Note Use the cable stripper listed in the Siemens IK 10 catalog in order to enable you to strip the insulation from the cables faster and to the proper length. Mobile Panel 177 (WinCC flexible)

  • Page 32: Connecting The Equipotential Bonding Circuit

    Mounting and Connection 4.2 Connecting the terminal box 4.2.6 Connecting the equipotential bonding circuit Potential differences Differences in potential between spatially separated system parts can lead to high equalizing currents via the data cables and therefore to the destruction of their interfaces. This situation may arise if the cable shields are fitted at both ends and grounded at different system parts.

  • Page 33: Connecting A Power Supply

    Mounting and Connection 4.2 Connecting the terminal box 4.2.7 Connecting a Power Supply Introduction The supply voltage for the HMI device is connected to a terminal strip in the terminal box. The terminal block is designed for cables with a maximum cross-section of 1,5 mm Connect the ground terminal of the terminal box to the cabinet ground.
  • Page 34 Mounting and Connection 4.2 Connecting the terminal box The abbreviations in the figure are defined as follows: • PE stands for equipment grounding conductor • M stands for ground • P24 stands for +24 VDC Please refer to Technical Data for information on the voltage supply requirements. Warning 24 V DC -supply Personal injury and equipment damage can occur.

  • Page 35: Connecting The Plc

    Mounting and Connection 4.2 Connecting the terminal box 4.2.8 Connecting the PLC Connecting a PLC to a Terminal Box DP The following figure shows the connection of the PLC to the Terminal Box DP. When a serial interface is used during operation, IF1 (RS 232) and (RS 422/485) may only be connected alternately at the terminal box Use only the cables approved for that purpose to connect to a SIMATIC S7.
  • Page 36 Mounting and Connection 4.2 Connecting the terminal box Configure the interfaces IF1 on the Terminal Box DP The IF1 interface can be configured using the DIL switch. The figure below shows the position of the DIL switch. Figure 4-11 Position of the DIL switch ①...
  • Page 37 Mounting and Connection 4.2 Connecting the terminal box Communication Switch setting Compressing the internal program memory with SIMATIC S5 Caution Compressing the internal program memory Compressing the internal program memory of the SIMATIC S5 PLC ("Compress" PU function, integrated FB COMPR) is not permitted if an HMI device is connected! When memory is compressed, the absolute addresses of the blocks in the program memory change.

  • Page 38: Connecting The Configuration Computer

    4.2 Connecting the terminal box 4.2.9 Connecting the configuration computer Introduction Standard cables are available for the connections shown (refer to the Siemens ST80 catalog). Connection configurator The following figures show the connection between the terminal box and the configuration computer via the network.
  • Page 39 Mounting and Connection 4.2 Connecting the terminal box Figure 4-13 Connect the configuration computer via PROFINET to a Terminal Box PN Mobile Panel 177 (WinCC flexible) 4-17 Operating Instructions (Compact), Edition 07/2005...

  • Page 40: Connecting Mobile Panel 177

    Mounting and Connection 4.3 Connecting Mobile Panel 177 Connecting Mobile Panel 177 4.3.1 Opening and closing the terminal compartment Introduction Before you begin: Caution Malfunctions If the HMI device lies on its front, the STOP button can trigger. Other operating elements (key-operated switches, illuminated pushbuttons) can be triggered unintentionally, thus causing malfunctions.
  • Page 41 Mounting and Connection 4.3 Connecting Mobile Panel 177 Procedure Figure 4-14 Opening the terminal compartment ① Cover ② Screws on the cover ③ Plugs ④ Outlet Proceed as follows: 1. Screw out the six screws of the cover about 1 cm The cover is designed in such a way that the screws cannot be lost.

  • Page 42: Interfaces On The Mobile Panel 177 Dp

    Mounting and Connection 4.3 Connecting Mobile Panel 177 4.3.2 Interfaces on the Mobile Panel 177 DP The following interfaces are available on the Mobile Panel 177 DP: Figure 4-15 Interfaces on the Mobile Panel 177 DP ① Slot with a MultiMediaCard ②...

  • Page 43: Interfaces On Mobile Panel 177 Pn

    Mounting and Connection 4.3 Connecting Mobile Panel 177 4.3.3 Interfaces on Mobile Panel 177 PN The following interfaces are available on the Mobile Panel 177 PN: Figure 4-16 Interfaces on Mobile Panel 177 PN ① Slot with MultiMediaCard ② RS 485 interface (IF 2) ③...

  • Page 44: Connecting The Connecting Cable

    Mounting and Connection 4.3 Connecting Mobile Panel 177 4.3.4 Connecting the connecting cable Introduction The connecting cable can be connected to the terminal box using the plug connector (metallic push-pull circular connector). The plug connector is coded anti-rotationally using a slot and key system.
  • Page 45 Mounting and Connection 4.3 Connecting Mobile Panel 177 Procedure – plugging the connector Proceed as follows: 1. Pull back the outer sleeve on the plug connector 2. With the outer sleeve retracted, insert the plug connector into the socket of the terminal box.

  • Page 46: Connecting The Configuration Computer

    Connecting the configuration computer to the Mobile Panel 177, example Mobile Panel 177 PN For the conversion from RS 232 to RS 485, order the PC-PPI adapter, Order No. 6ES7 901- 3CB30-0XA0, from Siemens AG. The interfaces are described in the Technical Data. Notice You cannot fasten the cover of the terminal compartment while a configuration computer is connected directly to the Mobile Panel 177.

  • Page 47: Operator Elements And Displays

    Operator elements and displays Mobile Panel 5.1.1 Operator control elements The Mobile Panel 177 has the following operator control elements: • Color STN-LC display, Q-VGA, with touch screen, analog, resistive • Membrane keyboard • Enable switch The Mobile Panel 177 offers the following optional elements: •...

  • Page 48: Front-Side Operator Control Elements

    Operator elements and displays 5.1 Mobile Panel 5.1.2 Front-side operator control elements Figure 5-1 Operator control elements of the Mobile Panel 177 ① STOP button ② Display with touch screen ③ Function keys without LED ④ Key-operated switch ⑤ Handwheel ⑥...

  • Page 49: Enable Switch

    Operator elements and displays 5.1 Mobile Panel 5.1.3 Enable switch Introduction Enabling equipment consists of two enabling switches arranged on both sides of the Mobile Panel 177. The switch setting of the two enabling switches is determined by electrical momentary contact switches. The associated evaluating logic involves two channels for each enabling switch.
  • Page 50 Operator elements and displays 5.1 Mobile Panel Switch settings The primary function of the evaluating logic is to recognize the three switch settings: Switch setting Function Enable switch Switch state Neutral position Not activated OFF (open) Enable Activated ON (closed) Panic Pressed OFF (open)

  • Page 51: Stop Button

    Operator elements and displays 5.1 Mobile Panel The position of the enabling switch can be scanned in the Mobile Panel 177 via the CPU and evaluated for non-safety relevant functions by the software. The safety shutdown does not require an acknowledgement when an enabling switch is released or pressed through to the panic setting! 5.1.4 STOP button...
  • Page 52 Operator elements and displays 5.1 Mobile Panel Figure 5-6 STOP button ① Fall protection ② STOP button Due to its placement, the STOP button is equally accessible to both left-handed and right- handed individuals. Due to its profiled design, the STOP button is easily accessible. The STOP button is fall protected by a special collar.

  • Page 53: Stop Button On Terminal Box Plus

    Operator elements and displays 5.1 Mobile Panel 5.1.4.2 STOP button on Terminal Box Plus Introduction A Terminal Box Plus differs from a Terminal Box Basic due to four relays that are mounted on the board. Figure 5-7 Terminal Box Plus ①...

  • Page 54: Stop Button On Terminal Box Basic

    Operator elements and displays 5.1 Mobile Panel The Stop or Emergency Stop circuit switching statuses for a connected Mobile Panel 177 without a STOP button and Terminal Box Plus are: Mobile Panel 177 STOP button Status of the Stop or Emergency Stop circuit Connected Not present The Stop or Emergency Stop circuit remains closed.
  • Page 55 Operator elements and displays 5.1 Mobile Panel Caution If the Mobile Panel 177 is connected, the Stop or Emergency Stop circuit is controlled via the STOP button. If the connecting cable of the Mobile Panel 177 is disconnected from the Terminal Box Basic, the Stop or Emergency Stop circuit is interrupted and a safe shutdown of the system being monitored or Emergency Stop is executed.

  • Page 56: Hand Wheel

    Operator elements and displays 5.1 Mobile Panel 5.1.5 Hand wheel Introduction The hand wheel is an optional control element at the Mobile Panel 177. The hand wheel can be turned without a stop and does not have a zero position. You can use the hand wheel to input incremental values.

  • Page 57: Key-Operated Switch

    Operator elements and displays 5.1 Mobile Panel 5.1.6 Key-operated switch Introduction The key switch is an optional control element of the Mobile Panel 177. The key switch is used to lock functions that are triggered by the Mobile Panel 177. The status of the key switch is evaluated as a direct button or via WinCC flexible system functions.

  • Page 58: Illuminated Pushbutton

    Operator elements and displays 5.1 Mobile Panel 5.1.7 Illuminated pushbutton Introduction The illuminated pushbutton is an optional control element on the Mobile Panel 177. The illuminated pushbutton is available for rapid digital inputs. The status of the illuminated pushbutton is evaluated as a direct button or via WinCC flexible system functions.

  • Page 59: Terminal Box Pn

    Operator elements and displays 5.2 Terminal Box PN Terminal Box PN Introduction Six LEDs that display the communication status are positioned on the front of the Terminal Box PN ① LED displays (green LED "LNK", yellow LED "ACT") Two LED displays "LNK" and "ACT" each exist for the following connections: •...
  • Page 60 Operator elements and displays 5.2 Terminal Box PN Mobile Panel 177 (WinCC flexible) 5-14 Operating Instructions (Compact), Edition 07/2005...

  • Page 61: Specifications

    Specifications Dimensional drawings 6.1.1 Mobile Panel Device dimensions Dimensions of Mobile Panel 177 Overall dimensions of the Mobile Panel 177 HMI device in the front view Mobile Panel 177 (WinCC flexible) Operating Instructions (Compact), Edition 07/2005...
  • Page 62 Specifications 6.1 Dimensional drawings Overall dimensions of the Mobile Panel 177 HMI device in the side view Mobile Panel 177 (WinCC flexible) Operating Instructions (Compact), Edition 07/2005...

  • Page 63: Wall Holder

    Specifications 6.1 Dimensional drawings 6.1.2 Wall holder Device dimensions Dimensions of wall mount Figure 6-1 Dimensions of wall mount Mobile Panel 177 (WinCC flexible) Operating Instructions (Compact), Edition 07/2005...

  • Page 64: Terminal Box Dp

    Specifications 6.1 Dimensional drawings 6.1.3 Terminal Box DP Device dimensions Dimensions of terminal box Figure 6-2 Dimensions of terminal box Mobile Panel 177 (WinCC flexible) Operating Instructions (Compact), Edition 07/2005...

  • Page 65: Terminal Box Pn

    Specifications 6.1 Dimensional drawings 6.1.4 Terminal Box PN Device dimensions Dimensions of the Terminal Box PN Figure 6-3 Dimensions of the Terminal Box PN Mobile Panel 177 (WinCC flexible) Operating Instructions (Compact), Edition 07/2005...

  • Page 66: Technical Data

    Specifications 6.2 Technical data Technical data 6.2.1 Mobile Panel HMI device Weight without packaging Approx. 1.3 kg Display Type Color-STN LCD Display area, active 115 mm x 86 mm (5.7") Resolution 320 x 240 pixels Colors, displayable 256 colors Contrast control Back-lighting CCFL Half Brightness Life Time, typical...

  • Page 67: Terminal Box Dp

    Specifications 6.2 Technical data Voltage supply Voltage supply Via terminal box Additional specifications Fall height max. 1.5 m 6.2.2 Terminal Box DP Terminal Box DP Weight without packaging Approx. 500 g Voltage supply Nominal voltage +24 V DC Range, permissible 20.4 V to 28.8 V (–15%, +20%) Transients, maximum permissible 35 V (500 msec)

  • Page 68: Terminal Box Pn

    Specifications 6.2 Technical data 6.2.3 Terminal Box PN Terminal Box PN Weight without packaging Approx. 700 g Voltage supply Nominal voltage +24 V DC Range, permissible 20.4 V to 28.8 V (–15%, +20%) Transients, maximum permissible 35 V (500 msec) Time between two transients, minimum 50 s Current consumption Terminal Box PN without panel...

  • Page 69: Interface Allocation Mobile Panel 177 Dp

    Specifications 6.3 Interface allocation Mobile Panel 177 DP Interface allocation Mobile Panel 177 DP 6.3.1 RS 485 (IF 2) Sub-d socket, 9-pin, with screw lock Figure 6-4 RS 485 interface pin assignment Assignment n. c. GND 24 V Data channel B (+) n.

  • Page 70: Female Header

    Specifications 6.4 Interface assignment Mobile Panel 177 PN 6.3.3 Female header Female header for the connecting cable Figure 6-6 Pin assignment of 10-pin female header Assignment Circuit +24 V DC Power supply GND 24 V Stop 23 Stop circuit Stop 24 Stop 13 Stop 14 Enable 1+...

  • Page 71: Rj45

    Specifications 6.4 Interface assignment Mobile Panel 177 PN 6.4.2 RJ45 RJ45 connector for the connecting cable Figure 6-8 Pin assignment of the RJ45 connector Assignment n. c. n. c. ICD+ ICD– 6.4.3 Female header Female header for the connecting cable Figure 6-9 Pin assignment of 12-pin female header Assignment...

  • Page 72: Interface Assignment Terminal Box Dp

    Specifications 6.5 Interface assignment Terminal Box DP Interface assignment Terminal Box DP Position of the ports Figure 6-10 Position of the ports ① Terminal strip 1 ② Fast connector ③ Terminal strip 2 Caution When connecting the cables to the terminal strips ensure that the assignments for Terminal strips 1 and 2 are not reversed.
  • Page 73 Specifications 6.5 Interface assignment Terminal Box DP Terminal strip 1: IF1 and power supply Figure 6-11 Assignment of 12-pin terminal strip 1 RS 232 RS 232 RS 422 RS 485 Power supply IF 1A IF 1A IF 1B IF 1B 9-pin 15-pin 9-pin...
  • Page 74 Specifications 6.5 Interface assignment Terminal Box DP Fast connector Figure 6-12 Assignment of 4-pin Fast Connector Assignment LTG-A (–) IN LTG-B (+) IN LTG-A (–) OUT LTG-B (+) OUT Terminal strip 2: Safety Functions and Supplemental Functions Figure 6-13 Assignment of 12-pin terminal strip 2 Internal interconnection Name Circuit...
  • Page 75 Specifications 6.5 Interface assignment Terminal Box DP Internal interconnection Name Circuit Enable 2+ Enable switch See Female header Enable 1– Enable 1+ Enable 2– Applies to Terminal Box Plus The Terminal Box Basic does not have the "STOP button pressed" signal. The "STOP button depressed"...

  • Page 76: Interface Assignment Terminal Box Pn

    Specifications 6.6 Interface assignment Terminal Box PN Interface assignment Terminal Box PN Position of the ports Figure 6-14 Position of the ports ① Fast connector ② Terminal strip 1 ③ Terminal strip 2 Fast connector The terminal box contains two fast connectors for connecting to PROFINET. Figure 6-15 Assignment of 4-pin fast connector Assignment...
  • Page 77 Specifications 6.6 Interface assignment Terminal Box PN Terminal strip 1: Power supply Figure 6-16 Assignment of 3-pin terminal strip 1 Power supply Terminal strip 2: Safety Functions and supplemental functions Figure 6-17 Assignment of 12-pin terminal strip 2 Internal interconnection Name Circuit Stop 13...

  • Page 78: Connection Examples For Enable Switch And Stop Button

    Specifications 6.7 Connection examples for Enable switch and STOP button "Mobile Panel plugged" signal Mobile Panel on the Terminal Box Signal at the digital input of the controller Not plugged "0" Plugged "1" Note The "Mobile Panel plugged" output of the Terminal Box Basic is connected to the power supply.
  • Page 79 Specifications 6.7 Connection examples for Enable switch and STOP button Connection example 1: Enabling switch with monitoring device ELAN SRB-NA-R-C.27/S1 The following figure shows the connection of a monitoring device ELAN SRB-NA-R-C.27/S1 to the enabling switch of the Mobile Panel. Figure 6-18 Wiring diagram: Enabling switch with monitoring device ELAN SRB-NA-R-C.27/S1 S1 and S4 switches on the rear of the module must be at Position 0.
  • Page 80 Specifications 6.7 Connection examples for Enable switch and STOP button Connection example 2: Enabling switch on monitoring device PILZ PST1 The following figure shows the connection of a monitoring device PILZ PST1 to the enabling switch of the Mobile Panel. Figure 6-19 Wiring diagram: Enabling switch on monitoring device PILZ PST1 Mobile Panel 177 (WinCC flexible)
  • Page 81 Specifications 6.7 Connection examples for Enable switch and STOP button Connection example 3: STOP button with SIGUARD 3TK2840 monitoring device The following figure shows the connection of a monitoring device SIGUARD 3TK2840 to the STOP button of the Mobile Panel. Figure 6-20 Wiring diagram: STOP button with SIGUARD 3TK2840 monitoring device Monitoring outputs may not be used for safety-related functions.
  • Page 82 Specifications 6.7 Connection examples for Enable switch and STOP button Mobile Panel 177 (WinCC flexible) 6-22 Operating Instructions (Compact), Edition 07/2005...

  • Page 83: Appendix

    Appendix Connection point recognition A.1.1 Overview Introduction You can divide a system into several zones or functional areas by using several terminal boxes. For this purpose it may be necessary for different system screens to be displayed, depending on the terminal box used. This is achieved by means of connection point recognition.

  • Page 84: Connection Point Recognition Via Box Id

    Appendix A.1 Connection point recognition Note The "Project ID" range pointer can be used to ensure that the HMI device is connected to the PLC that forms the basis of the project. The "Project ID" range pointer can be assigned to only one PLC for each project (see "WinCC flexible Communication"...
  • Page 85 Appendix A.1 Connection point recognition 4. Select the "Internal_Box-ID" tag in the "Settings for runtime" section at the "Access point". When you connect the HMI device to the terminal box, the box ID is written automatically into the "Internal_Box-ID" tag. 5.
  • Page 86 Appendix A.1 Connection point recognition 9. Select the system function "SetValue" from the "Calculation" group. Select the "External_Box-ID" tag at "Tag (output)". Select the "Internal_Box-ID" tag at "Value". Result The box ID of the terminal box to which the Mobile Panel 177 is connected is transferred to the controller.

  • Page 87: Evaluation Of The Operator Control Elements

    Appendix A.2 Evaluation of the operator control elements Evaluation of the operator control elements A.2.1 Overview Operator control elements The following information can be transferred between the HMI device and the controller: • Direction pulses of the handwheel • Status of the softkeys •...

  • Page 88: Evaluating Operator Control Elements As Direct Keys

    Appendix A.2 Evaluation of the operator control elements A.2.2 Evaluating operator control elements as direct keys Introduction You can configure the operator control elements of the HMI device as direct keys. Direction pulses of the handwheel and the switch state of the softkeys, key-operated switch, or illuminated pushbutton are then directly available in the I/O area of the PLC.
  • Page 89 Appendix A.2 Evaluation of the operator control elements Bit coding The following tables show the bit coding for softkeys, key-operated switch, illuminated pushbutton and handwheel: • Bit coding of fsoftkeys Status F1 to F14 Not pressed Pressed • Bit coding of LEDs of softkeys Status F1 to F8 LED not illuminated...
  • Page 90 Appendix A.2 Evaluation of the operator control elements • Bit coding of handwheel – A setpoint is not specified for the handwheel. – After startup of the HMI device, bytes n+3 to n+4 (see figure) are set to zero. Rotation of the handwheel produces positive or negative pulses depending on the rotation direction.

  • Page 91: Evaluating Operator Control Elements Via Wincc Flexible System Functions

    Appendix A.2 Evaluation of the operator control elements Response time Bytes n+3 and n+4 must be scanned on the PLC side within a second and cyclically. This ensures that no more than 256 pulses can be added between two scans of the handwheel. For 256 pulses, approximately 4.5 revolutions of the handwheel are required.
  • Page 92 Appendix A.2 Evaluation of the operator control elements A.2.3.2 Basic procedure Introduction You can use WinCC flexible system functions to evaluate the operator control elements of the HMI device or to control the LEDs of the softkeys and of the illuminated pushbutton. Direction pulses of the handwheel and the switch state of the softkeys, key-operated switch, or illuminated pushbutton are then transferred via tags to the PLC.
  • Page 93 Appendix A.2 Evaluation of the operator control elements 3. For illuminated pushbuttons, key-operated switches and handwheels (global assignment): Open the template in the "Screens" editor. Select the operator control element in the template. Click on the "General" group in the properties window. Select the "Status_Control_Element"...
  • Page 94 Appendix A.2 Evaluation of the operator control elements 7. Select the system function "SetValue" from the "Calculation" group. Select the "Control_Element_PLC" tag at "Tag (output)". Select the "Status_Control_Element" tag at "Value". 8. When communication is established, the possibly old value currently existing in the controller is then written automatically into the "Control_Element_PLC"...

  • Page 95: Illuminated Pushbutton

    Appendix A.2 Evaluation of the operator control elements A.2.3.3 Illuminated pushbutton Application The illuminated pushbutton is an optional operator control element of the Mobile Panel 177. The integrated LED can be actuated from the PLC. The LED can assume the following states: •...

  • Page 96: Key-Operated Switch

    Appendix A.2 Evaluation of the operator control elements A.2.3.4 Key-operated switch Application The key-operated switch is an optional operator control element of the Mobile Panel 177. In an active project the key-operated switch is used to lock functions that are triggered by the Mobile Panel 177.
  • Page 97 Index Application Design, 1-1 Handwheel, A-14 Wall holder, 1-9 Illuminated pushbutton, A-13 Direct keys, A-5 Key-operated switch, A-14 Display, 6-6 LED of the softkeys, A-9 Enable switch, 5-3 Box ID, A-1 Normal activation, 5-4 Byte assignment, A-6 Panic activation, 5-4 Switch settings, 5-4 Equipotential bonding Connecting, 4-10...
  • Page 98 Index Operator control elements, 5-1, 5-2 Overall dimensions IF1 interface Mobile Panel 177, 6-1, 6-2 Assignment, 6-13, 6-17 Illuminated pushbutton, 5-12 Application, A-13 Bit assignment, A-13 Input unit, 6-6 Panic activation, 5-4 Installation Configuration computer, 4-16 Connecting, 4-16 Interfaces, 4-5, 4-6, 4-16, 4-20, 4-21 Pin assignment Configuring, 4-14 Female header, 6-10, 6-11...
  • Page 99 Index Technical specifications Display, 6-6 HMI device, 6-6, 6-7, 6-8 Input unit, 6-6 Memory, 6-6 Overall dimensions, 6-1, 6-2 RS 485 interface, 6-9, 6-10 Voltage supply, 6-7, 6-8 Terminal box DIL switch, 4-14 Fast connector, 6-16 IF1 interface, 6-17 Interfaces, 4-5, 4-6 Terminal strip 1, 6-17 Terminal strip 2, 6-17 Variants, 1-7...

  • Page 100: Index

    Index Mobile Panel 177 (WinCC flexible) Index-4 Operating Instructions (Compact), Edition 07/2005...

Table of Contents