Advertisement
Quick Links
CISCO MV13-HW
安裝指南
Installation Guide
Overview
The Cisco Meraki MV13 is a networked camera that is exceptionally simple to deploy and configure due to its integration
into the Meraki dashboard and cloud augmented edge storage. The MV family eliminates the complex and costly servers
and video recorders required by traditional solutions, removing the limitations typically placed on video surveillance
deployments.
Specifications
(3840x2160)
(2560 x 1440)
(1920x1080)
Networking and Wireless
•
1x 10/100/1000 Base-T Ethernet (RJ45) DSCP traffic marking
•
Supported frequency bands (country-specific restrictions apply):
•
2.4 GHz 802.11b/g/n radio：
•
2.400 - 2.483.5 GHz
•
5 GHz 802.11a/n/ax radio：
•
5.150 - 5.250 GHz (UNII-1)
5.250 - 5.350 GHz (UNII-2)
5.470 - 5.600, 5.650 - 5.725 GHz (UNII-2e) 5.725 - 5.850 GHz (UNII-3)
•
1x1 with one spatial stream
•
MU-MIMO support
20 and 40 MHz channels (802.11n)
20, 40, and 80 MHz channels (802.11ax)
Up to 256 QAM on both 2.4 GHz and 5 GHz bands
•
2.4 GHz Bluetooth Low Energy (BLE, EDR, BR) radio
Package Contents
In addition to the MV camera, the following are provided:
Phillips head wall mounting screws
•
Wall screw anchors for masonry (brick, concrete)
•
Torx key
•
概覽
規格
包裝內容
Advertisement
Related Manuals for Cisco Meraki MV13
Summary of Contents for Cisco Meraki MV13
- Page 1 Overview 概覽 The Cisco Meraki MV13 is a networked camera that is exceptionally simple to deploy and configure due to its integration into the Meraki dashboard and cloud augmented edge storage. The MV family eliminates the complex and costly servers and video recorders required by traditional solutions, removing the limitations typically placed on video surveillance deployments.
- Page 2 Wall mount plate • Ethernet Port / Power The MV13 features a 1000BASE-T Ethernet port that supports 802.3af Power-over-Ethernet (PoE). Pre-Install Preparation You should complete the following steps before going on-site to perform an installation. Configure Your Network in Dashboard The following is a brief overview only of the steps required to add an MV13 to your network.
- Page 3 Each MV13 will generate a unique domain name to allow secured direct streaming functionality. These domain names resolve an A record for the private IP address of the camera. Any public recursive DNS server will resolve this domain. If utilizing an on-site DNS server, please whitelist *.devices.meraki.direct or configure a conditional forwarder so that local domains are not appended to *.devices.meraki.direct and that these domain requests are forwarded to Google public DNS.
- Page 4 wall in pre-determined locations. Use template holes to align the mounting plate. 3. Connect PoE cable to the camera.
- Page 5 4. Turn bubble counterclockwise to unlock and remove. While the bubble is released, aim the lens to the desired scene. 5. Align camera to mounting plate studs. Slide the camera onto studs and turn the camera clockwise to secure the top plate. If the cable run is not coming directly behind the camera, the cable guard will need to be removed.
- Page 6 examples.
- Page 8 6. Further secure camera to mounting plate by tightening the green security screw. 7. Aim the lens. Inspect the camera feed on the Meraki Dashboard to fine-tune the picture. The camera sensor and lens unit can be physically tilted through a range of 65 degrees, rotated through a range of 350 degrees, and panned through a range of 350 degrees.
- Page 9 adjusted on the camera.
- Page 10 8. Replace the plastic dome. Turn dome clockwise to lock. 9. Remove the protective cap from the camera bubble.
- Page 11 Powering the MV13 Remove the cable guard and route the Ethernet cable from an active port on an 802.3af PoE switch or PoE injector. Note: PoE supports a maximum cable length of 300 ft (100 m). WLAN Capability MV13 cameras running MV firmware 3.16 and newer can be configured as wireless clients. To learn how to configure MV13 wireless settings, check out our MV Wireless Configuration Guide.
- Page 12 • Consult the dealer or an experienced radio/TV technician for help. FCC Caution Any changes or modifications not expressly approved by Cisco Systems, Inc. could void the user’s authority to operate this equipment. This Transmitter must not be co-located or operation in conjunction with any other antenna or transmitter.
- Page 13 For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent ê t re exploités.
- Page 14 Europe-EU/UK Declaration of Conformity Scope The information in this document is applicable to the Cisco Meraki MV13-HW This product is intended to be placed on the market within the European Union, Lichtenstein, Switzerland, Iceland, Norway, Turkey and other countries that have implemented the EU Directive 2014/53/EU & Radio Equipment Regulations 2017 (S.I.
- Page 15 This declaration is only valid for configurations (combinations of software, firmware and hardware) provided and/or supported by Cisco Systems for use within the EU or countries that have implemented the EU Directives and/or spectrum regulation. The use of software or firmware not supported/provided by Cisco Systems may result in equipment no longer compliant with the regulatory requirements.
- Page 16 (2) Este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada. Taiwan RoHS Statement CS-0438 - 台灣 RoHS 台灣 RoHS“限用物質含有情況標示聲明書”網址 www.cisco.com/go/taiwanrohs Statement CS-0438 - Taiwan RoHS Taiwan RoHS “Restricted Substances Content Disclosure Table” web address www.cisco.com/go/taiwanrohs...