hit counter script
LG 42PM1M -  - 42" Plasma Panel Service Manual
LG 42PM1M -  - 42" Plasma Panel Service Manual

LG 42PM1M - - 42" Plasma Panel Service Manual

Service manual
Hide thumbs Also See for 42PM1M - - 42" Plasma Panel:

Advertisement

PLASMA MONITOR

SERVICE MANUAL

CHASSIS : RF-052A
MODEL : 42PM1M
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
42PM1M-TA
website:http://biz.LGservice.com
e-mail:http://www.LGEservice.com/techsup.html

Advertisement

Table of Contents
loading

Summary of Contents for LG 42PM1M - - 42" Plasma Panel

  • Page 1: Plasma Monitor

    website:http://biz.LGservice.com e-mail:http://www.LGEservice.com/techsup.html PLASMA MONITOR SERVICE MANUAL CHASSIS : RF-052A MODEL : 42PM1M 42PM1M-TA CAUTION BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
  • Page 2: Table Of Contents

    CONTENTS SAFETY PRECAUTIONS ..................3 DESCRIPTION OF CONTROLS ................4 SPECIFICATIONS ....................8 ADJUSTMENT INSTRUCTIONS ...............10 TROUBLE SHOOTING GUIDE ................15 PRINTED CIRCUIT BOARD ................24 BLOCK DIAGRAM .....................26 EXPLODED VIEW ....................28 EXPLODED VIEW PARTS LIST ................29 REPLACEMENT PARTS LIST................30 SCHEMATIC DIAGRAM..................- 2 -...
  • Page 3: Safety Precautions

    SAFETY PRECAUTIONS IMPORT ANT SAFETY NOTICE Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards.
  • Page 4: Description Of Controls

    DESCRIPTION OF CONTROLS MUTE POWER MUTE POWER switches the sound on or off. switches the set on from standby or off to standby. INPUT MULTIMEDIA I/II MULTIMEDIA selects the Component, RGB or DVI I/II (option) modes. selects the language during dual lan- LIST/ MENU guage broadcast.
  • Page 5 <Front Panel Controls> ON/OFF ON/OFF 1. Main Power Button 5. MENU Displays on screen menus one by one. 2. Remote Control Sensor Exits the current menu. Memorizes menu changes. 3. Power Standby Indicator Illuminates red in standby mode, Illuminates green when the set is turned on Selects a menu option.
  • Page 6: Back Panel

    <Back Panel> AUDIO COMPONENT INPUT 2 MONITOR OUPUT REMOTE RGB OUTPUT CONTROL COMPONENT INPUT 1 A/V INPUT AC INPUT (MONO) (MONO) RS-232C INPUT HDMI/ EXTERNAL SPEAKER AUDIO INPUT RGB INPUT VARIABLE AUDIO OUT (CONTROL/SERVICE) DVI(VIDEO) VIDEO AUDIO AUDIO VIDEO S-VIDEO AUDIO Connection to PC Connection to AV equipment...
  • Page 7 MUTE POWER INPUT MULTIMEDIA I/II LIST/ MENU SPLIT ZOOM TEXT/ SLEEP REVEAL MODE SIZE UPDATE Q.VIEW TIME HOLD INDEX Owner’s Manual Remote Control handset 1.5V Alkaline batteries Power Cord Optional Extras Optional extras can be changed or modified for quality improvement without any notification new optional extras can be added.
  • Page 8: Specifications

    SPECIFICATIONS NOTE : Specifications and others are subject to change without notice for improvement. Application Range This spec is applied to the 42”PDP TV used RF-052A Chassis. Specification Each part is tested as below without special appointment. 1) Temperature : 25±5°C (77±9°F), CST : 40±5 2) Relative Humidity: 65 ±...
  • Page 9 2. Model Specification Item Specification Remark Market Non-EU Broadcasting system PAL B/G/I/D/K, NTSC BAND Available Channel E2~E12 E21~E69 CATV S1~S47 HYPER S1~S20 Upper Heterodyne Receiving system Video Input (1EA) PAL, SECAM, NTSC Except 42PM1MB, 50PM1MB, 42PM3MVB Video Output(1EA) PAL, SECAM, NTSC Except 42PM1MB, 50PM1MB, 42PM3MVB S-Video Input(1EA) PAL, SECAM, NTSC...
  • Page 10: Adjustment Instructions

    ADJUSTMENT INSTRUCTIONS 1. Application Object 3-2. Channel memory Method 1) Select “PDP” and “Hurricane” on Model dialog. And check These instructions is applied all of the 42” PDP TV, RF-052A your connection in Communication dialog. (If your Chassis. connection is ‘NG’, then set your PORT(COM1,2,3,...) correctly.) 2.
  • Page 11: Adjustment Method

    5-2. Setting of device Each PCB assembly must be checked by check JIG set. (Because power PCB Assembly damages to PDP Module, especially be careful) 4. POWER PCB Assy Voltage Adjustments (Va, Vs Voltage Adjustments) 4-1. Test Equipment : D.M.M. 1EA (Fig.
  • Page 12: Required Equipment

    7. Adjustment of White Balance 7-1. Required Equipment 1) Remote controller for adjustment 2) Color Analyzer (CA-100 or same product) 3) Auto W/B adjustment instrument(only for Auto adjustment) 4) AV Pattern Generator 7-2. Connecting diagram of equipment for measuring (For Auto Adjustment) COLOR ANALYZER 216 Level (85 IRE)
  • Page 13: Required Test Equipment

    6) Stick sensor to center of the screen and select each items (Red/Green/Blue Gain and offset) using (CH +/-) key on R/C. 7) Adjust Only High Light with R Gain/ B Gain using (VOL+/-) key on R/C. 8) Adjust it until color coordination becomes as below. (Initially, R/G/B gain and R/G/B offset values are fixd Red Gain : 82, Green Gain : 80, Blue Gain : 86 Red Offset : 7D, Green Offset : 7E, Blue Offset : 80)
  • Page 14 10. Default value in adjustment mode 10-1. Auto Color Balance (Component/RGB) Auto Color Balance(HEX) Auto-RGB To Set Source Cortez Offset1 Green Offset1 Blue Offset1 Offset2 Green Offset2 Blue Offset2 Gain Green Gain Blue Gain Reset To Set (Fig. 11) Default Value on OSD 10-2.
  • Page 15: Trouble Shooting Guide

    TROUBLE SHOOTING GUIDE 1. Power Board 1-1. The whole flowchart which it follows in voltage output state Start check Is it identical Doesn't the Is the Interface screen whole come with Power Off signal operated? out? condition? 1. Check the Power Off 2.
  • Page 16 1-2. Sony Power Board Structure T502: Vs Trans T702: Va Trans T101: St-by Trans T103: Low Voltage Trans - 16 -...
  • Page 17 1-3. Sanken, LGIT Power Board Structure T221: Vs Trans T271: Va Trans T121: St-by Trans T201: Low Voltage Trans - 17 -...
  • Page 18: No Power

    2. No Power (1) Symptom Does’t minute discharge at module. ¯ Non does not come in into the front LED. ¯ (2) Check following Is plug in power cord? Plug in power cord. Is the Line Filter and Power Connect the Cable. Board Cable connected? Is the Fuse(F101) on Replace the Fuse.
  • Page 19: Protect Mode

    3. Protect Mode (1) Symptom After once shining, it does not discharge minutely ¯ from module The Rely falls(The sound is audible “click”) ¯ It is converted with the color where the front LED ¯ is red from green. (2) Check following Is the Power Board Is output the normality Low/High Replace Power...
  • Page 20 4. No Raster (1) Symptom Does’t minute discharge at module. ¯ It maintains the condition where the front LED is green. ¯ (2) Check following Is the Power Board Is output the normality Low/High Replace the normal? voltage except Stand-by 5V? Power Board.
  • Page 21 5. In case of occurring strange screen into specific mode 5-1. In case the OSD does not displayed (1) Symptom LED is green ¯ The minute discharged continuously becomes ¯ accomplished from module (2) Check following Is the LVDS cable Is the LVDS cable Replace the cable.
  • Page 22 5-2. In case of does’t display the screen into specific mode (1) Symptom The screen does not become the display from specific input mode ¯ (RF, AV, Component, RGB, DVI). (2) Check following Check the all input mode should become normality display. ¯...
  • Page 23 6. In case of no sound (1) Symptom LED is green ¯ Screen display but sound is not output ¯ (2) Check following Is the SPK cable Is the SPK cable Replace SPK cable normal? connected well? Cable inserts well. Is the RF/ AV/ Does IC400 Does IC401...
  • Page 24: Printed Circuit Board

    PRINTED CIRCUIT BOARD MAIN(TOP) MAIN(BOTTOM) - 24 -...
  • Page 25 RCA(TOP) RCA(BOTTOM) CONTROL POWER SWITCH - 25 -...
  • Page 26: Block Diagram

    BLOCK DIAGRAM - 26 -...
  • Page 27 - 27 -...
  • Page 28: Exploded View

    EXPLODED VIEW - 28 -...
  • Page 29: Exploded View Parts List

    EXPLODED VIEW PARTS LIST Part No. Descriptions 5900V06008B FAN,DC G6015S12B2-RG DONGYANG 60*60*15 7V 1900RPM 6/12V L=500MM 5900V12006C FAN,DC B1232S12B2-AA DONGYANG 120*120*32 12V 7.8CFM 950RPM DC9-14V 4980V00D43B SUPPORTER, FAN SECC(EGI) MZ-42PM10 PRESS 4980V00E47A SUPPORTER, FAN SECC(EGI) SUPP.BLOWER FAN 6348Q-E074Z PDP, 42” 1024*768 PDP42X20022.AKLGG 6871QCH038A PWB(PCB) ASSEMBLY,DISPLAY CTRL ASSY HAND INSERT 42X2 CTRL LGDP4023,4013 6871QDH068A...
  • Page 30: Replacement Parts List

    REPLACEMENT PARTS LIST LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION Q1401 0TR387500AA CHIP 2SC3875S(ALY) BK KEC Q1402 0TR387500AA CHIP 2SC3875S(ALY) BK KEC 0IPRPML001A IC1000 MIC39100 MICREL 3P SOT223 R/TP Q300 0TR387500AA CHIP 2SC3875S(ALY) BK KEC 0IMCRRH001A IC1001 BA033FP-E2 ROHM 3P-SOP,TO252-3 CHIP 2SC3875S(ALY) BK KEC Q301...
  • Page 31 For Capacitor & Resistors, CC, CX, CK, CN : Ceramic RD : Carbon Film the charactors at 2nd and 3rd CQ : Polyestor RS : Metal Oxide Film digit in the P/No. means as CE : Electrolytic RN : Metal Film follows;...
  • Page 32 For Capacitor & Resistors, CC, CX, CK, CN : Ceramic RD : Carbon Film the charactors at 2nd and 3rd CQ : Polyestor RS : Metal Oxide Film digit in the P/No. means as CE : Electrolytic RN : Metal Film follows;...
  • Page 33 BK2125 HS 750 2X1.25X0.85MM R/TP SWITCH L116 6210VC0005A BK2125 HS 750 2X1.25X0.85MM R/TP MLB-201209-1000L-N2 1000OHM 350MA SW102 140-313B TACT 2LEAD 160G(TA) LG C&D 5V 0.001A L119 6200JB8010L 140-313B TACT 2LEAD 160G(TA) LG C&D 5V 0.001A 6200JB8010L MLB-201209-1000L-N2 1000OHM 350MA SW103...
  • Page 34 JK400 6612JH003CA PPJ137A AUDIO L-MONO JACK JK502 6612F00006F KJA-PH-3-0064 KSD 3.5PHI 14P DUALJACK ACCESSORIES 3828VA0544A MANUAL,OWNERS LG EN 138D TX 6710V00138L REMOTE CONTROLLER,W/O EYE MT-42PM15X 6410VEH003C POWER CORD,M2511A-001 VDE/SEMKO 2800MM 366-017A PIN,DRAWING SUB STAPLE NO.10 D0.3 L1 . MISCELLANEOUS 6850J00005A...
  • Page 39 Jun., 2005 P/NO : 3828VD0223D Printed in Korea...

This manual is also suitable for:

42pm1m-ta42pm1m

Table of Contents