Accessories; Cleaning The Laser Light Lens; Replacing Carbon Brushes; After Use - Makita LS1016 Instruction Manual
Slide compound miter saw
Hide thumbs
Also See for LS1016:
- Instruction manual (152 pages) ,
- Technical information (37 pages) ,
- Instruction manual (140 pages)
Table of Contents
Advertisement
Available languages
Available languages
To shift the laser line movable range further away from
the side surface of blade, turn the two screws counter-
clockwise after loosening the adjusting screw. Turn these
two screws clockwise to shift it closer to the side surface
of the blade after loosening the adjusting screw.
Refer to the section titled "Laser beam action" and adjust
the adjusting screw so that the cutting line on your work-
piece is aligned with the laser line.
NOTE:
• Check the position of laser line regularly for accuracy.
• Have the tool repaired by a Makita authorized service
center for any failure on the laser unit.
Cleaning the laser light lens (Fig. 65 & 66)
For models LS1016L and LS1016FL only
If the lens for the laser light becomes dirty, or sawdust
adheres to it in such a way that the laser line is no longer
easily visible, unplug the saw and remove and clean the
lens for the laser light carefully with a damp, soft cloth.
Do not use solvents or any petroleum-based cleaners on
the lens.
To remove the lens for the laser light, remove the saw
blade before removing the lens according to the instruc-
tions in the section titled "Installing or removing saw
blade".
Loosen but do not remove the screw which secures the
lens using a screwdriver.
Pull out the lens as shown in the figure.
NOTE:
• If the lens does not come out, loosen the screw further
and pull out the lens again without removing the screw.
Replacing carbon brushes (Fig. 67 & 68)
Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes.
Use a screwdriver to remove the brush holder caps. Take
out the worn carbon brushes, insert the new ones and
secure the brush holder caps.
After replacing brushes, plug in the tool and break in
brushes by running tool with no load for about 10 min-
utes. Then check the tool while running and electric
brake operation when releasing the switch trigger. If the
electric brake is not working correctly, have the tool
repaired by a Makita service center.
After use
• After use, wipe off chips and dust adhering to the tool
with a cloth or the like. Keep the blade guard clean
according to the directions in the previously covered
section titled "Blade guard". Lubricate the sliding por-
tions with machine oil to prevent rust.
• When storing the tool, pull the carriage toward you fully
so that the slide pole is thoroughly inserted into the turn
base.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be per-
formed by Makita Authorized Service Centers, always
using Makita replacement parts.
ACCESSORIES
WARNING:
• These accessories or attachments are recom-
mended for use with your Makita tool specified in
this manual. The use of any other accessories or
attachments may result in serious personal injury.
• Only use the Makita accessory or attachment for its
stated purpose. Misuse of an accessory or attach-
ment may result in serious personal injury.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Steel & Carbide-tipped saw blades
For smooth and precise cutting in
Miter saw blades
various materials.
General purpose blade for fast
Combination
and smooth rip, crosscuts and
miters.
For smoother cross grain cuts.
Crosscutting
Slices cleanly against the grain.
For sand-free cuts cleanly against
Fine cross cuts
the grain.
For miters in aluminum, copper,
Non-ferrous metals
brass, tubing, and other non-fer-
miter saw blades
rous metals.
• Vise assembly (Horizontal vise)
• Vertical vise
• Socket wrench 13
• Holder
• Dust bag
• Crown molding stopper set
• Triangular rule
• Dust box
• Hex wrench (For LS1016L and LS1016FL)
25
Hide quick links:
Advertisement
Table of Contents
