Summary of Contents for LG Flatron M1510A (M1510A-BZB.AN**LF)
Page 1
Service Guide Specification Service Guide Specification 담 당 관 리 자 LEE H.J KIM J.O Model Description 05.12.15 05.12.15 M1510A-BZB MODEL M1710A-BZB BRAND M1910A-BZB Part No. 3828TSL094Q FLATRON M1510A SUFFIX SNRULFT Product Name FLATRON M1710A FLATRON M1910A Printing Specification 1. Trim Size (Format) : 215mm x 280 mm 2.
Page 2
P/NO. Pagination sheet 3828TSL094Q Pagination sheet Total pages :40pages Front cover English English English English English Cover Inside blank …. ….. English English English English English Rear cover Rear Inside Cover …. blank blank blank...
Page 3
Website:http://biz.LGservice.com E-mail:http://www.LGEservice.com/techsup.html COLOR MONITOR SERVICE MANUAL CHASSIS NO. : CL-78 MODEL: M1510A (M1510A-BZB.AN**LF) M1710A (M1710A-BZB.AN**LF) M1910A (M1910A-BZB.AN**LF) ) **Same model for Service CAUTION BEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL. SOURCE MENU < VOL > AUTO/SELECT...
PRECAUTION WARNING FOR THE SAFETY-RELATED COMPONENT. WARNING BE CAREFUL ELECTRIC SHOCK ! • There are some special components used in LCD monitor that are important for safety. These parts are • If you want to replace with the new backlight (CCFL) or marked on the schematic diagram and the inverter circuit, must disconnect the AC adapter...
SERVICING PRECAUTIONS CAUTION: Before servicing receivers covered by this 9. Use with this receiver only the test fixtures specified in service manual and its supplements and addenda, read this service manual. and follow the SAFETY PRECAUTIONS on page 3 of this CAUTION: Do not connect the test fixture ground strap publication.
Page 8
General Soldering Guidelines Replacement 1. Use a grounded-tip, low-wattage soldering iron and 1. Carefully insert the replacement IC in the circuit board. appropriate tip size and shape that will maintain tip 2. Carefully bend each IC lead against the circuit foil pad and solder it.
Page 9
Circuit Board Foil Repair At Other Connections Excessive heat applied to the copper foil of any printed Use the following technique to repair the defective copper circuit board will weaken the adhesive that bonds the foil pattern at connections other than IC Pins. This technique to the circuit board causing the foil to separate from or involves the installation of a jumper wire on the "lift-off"...
TIMING CHART(M1510A) VIDEO SYNC Total Video Blanking Sync Back Front Mode Section Polarity Frequency Period Active Time Duration Porch Porch Resolution Clock ( B ) ( C ) ( E ) Time ( A ) ( D ) ( F ) H(Pixels) 25.175 31.468 KHz...
Page 11
TIMING CHART(M1710A,M1910A) VIDEO SYNC Total Front Back Display Sync. Period Porch Mode Section Polarity Frequency Porch Resolution Clock ( A ) ( C ) ( E ) ( D ) ( B ) H(Pixels) 25.175 31.469 640 x 350 V(Lines) 70.09 H(Pixels) 28.321...
DISASSEMBLY Remove the screws. Disassembly Back door. Remove the screws. Open the Backcover's latch with Jig. Remove the 4 screws of metal frame. Disassemble back cover. - 9 -...
Page 13
Remove the 6 screws from each side of metal frame. Pull out the control pcb. # 10 Remove the 6 screws from each side of metal frame. Remove the 4 screws from each side of metal frame. - 10 -...
DESCRIPTION OF BLOCK DIAGRAM 1. Power Supply Block (LIPS) 1) M1710A / 1910A This Block Generates DC Voltage (5V,15V) to Main Control system from AC Power (100-240 V, 50/60 Hz, 1.0A) Also it has the inverter function that converts input voltage to AC Rms value for the LCD lamp. 2) M1510A This Block Generates DC Voltage (5V,12V) to Main Control system from AC Power (100-240 V, 50/60 Hz, 1.0A) Also it has the inverter function that converts input voltage to AC Rms value for the LCD lamp.
LIPS Board Block Diagram 50 ~ 60Hz 100KHz HVDC ENERGY INPUT RECTIFIER OUTPUT RECTIFIER TRANSFER COMPONENTS AND FILTER AND FILTER LINE 100 ~ 240V SIGNAL PHOTO COLLENT- CONTROL -COUPLER CIRCUIT ISOLATION PRIMARY SECONDARY Operation description_LIPS 1. EMI components. This part contains of EMI components to comply with global marketing EMI standards like FCC,VCCI CISPR, the circuit included a line-filter, across line capacitor and of course the primary protection fuse.
ADJUSTMENT Windows EDID V1.0 User Manual 2. EDID Read & Write 1) Run WinEDID.exe Operating System: MS Windows 98, 2000, XP Port Setup: Windows 98 => Don’t need setup Windows 2000, XP => Need to Port Setup. This program is available to LCD Monitor only. 1.
SERVICE OSD ■ Description of operation Service Menu - Auto ADC : Adjust the White Balance Auto RGB menu - Audio : SVC and Engineering menu ( Not adjust) Auto ADC - Option 1, 3 : Adjust the option (Not adjust Option 2) Audio - Scaler DownLoad : Scaler Down Load menu Option 1...
TROUBLESHOOTING GUIDE 1. NO POWER (LED INDICATOR OFF) NO POWER (LED INDICATOR OFF) : [A] PROCESS CHECK SHORT OF MAIN CHECK 15V OR 5V B/D OR CHANGE LIPS OR LIPS CHECK OUTPUT OF CHANGE Q301, Q302, Q303 Q301,Q302,Q303 CHECK CHANGE U309, U310, U311 OUTPUT OF U309,U310,U311 CHANGE LED &...
Page 20
2. NO RASTER NO RASTER : [B] PROCESS CHECK LED STATUS REPEAT [A] PROCESS ON DISPLAY UNIT CHECK L401, L402, CHANGE L401, L402, L403 L403 CHECK THE CHANGE U401 INPUT/OUTPUT OF U401 CHANGE INVERTER CHECK INVERTER CONNECTOR OR CONNECTOR OR INVERTER INVERTER CHANGE PANEL LINK...
Page 21
3. NO RASTER ON AV, TV(RF) SINGAL NO RASTER ON AV SINGAL NO RASTER ON (VIDEO, S-VIDEO) TV(RF) SINGAL CHECK 5V,33V OF TU802 CHECK THE OUTPUT RE-SOLDERING OR REPEAT [A] PROCESS OF TU802 CHANGE THE DEFECT PART CHECK THE SIGNAL OF CHANGE L910, L911, L913 L910, L911, L913 RE-SOLDERING OR...
4. NO SOUND NO SOUND CHECK CHANGE SOURCE INPUT THE INPUT SOURCE RE-SOLDERING OR CHECK THE CHANGE THE DEFECT INPUT/OUTPUT PART CHECK X601 OF U601 CHECK THE RE-SOLDERING OR INPUT/OUTPUT OF U201 CHANGE THE DEFECT (or U203 Only 15 inch) ¡...
LCD(LIQUID CRYSTAL DISPLAY), LM170E01-TLA2 LG PHILPS TFT COLOR P6,645CH,250NITS,8MS,LPL NJ/KUMI,PB FREE,EGI,OKI S D-IC,SXGA,LVDS or 6304FLP298A LCD(LIQUID CRYSTAL DISPLAY), LM170E01-TLAA LG PHILPS TFT COLOR DOT FREE OF LM170E01-TLA1 LG PHILPS TFT COLOR P5,645CH,250NITS,8MS or 6304FLP299A LCD(LIQUID CRYSTAL DISPLAY), LM170E01-TLAB LG PHILPS TFT COLOR DOT FREE OF LM170E01-TLA2 LG PHILPS TFT COLOR P6,645CH,250NITS,8MS...
REPLACEMENT PARTS LIST CAUTION: BEFORE REPLACING ANY OF THESE COMPONENTS, READ CAREFULLY THE SAFETY PRECAUTIONS IN THIS MANUAL. * NOTE SAFETY Mark AL ALTERNATIVE PARTS DATE: 2005. 11. 30. DATE: 2005. 11. 30. *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION *S *AL LOC.