Page 1
Operator’s manual 343O3 Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. English...
KEY T O SYMBOLS Symbols The engine is s witched off by moving the stop switch to the stop position. W ARNING! The machine can be a CAUTION! The stop switch dangerous tool if used incorrectly or automatically returns to the start carelessly, which can cause serious position.
CONTENTS Contents Note the following before starting: KEY TO SYMBOLS Symbols ..............Please read the operator’s manual carefully. CONTENTS Contents ..............WARNING! Long-term exposure to Note the following before starting: ......noise can result in permanent hering impairment. So always use approved INTRODUCTION hearing protection.
The business concept is to develop, manufacture and market motor driven products for forestry and gardening as well as for building and construction industry. Husqvarna ′ s aim is also to be in the front edge according to ergonomics, usability, security and environmental protection.
GENERAL SAFETY PRECA UTIONS Impor tant Personal protective equipment IMPORTANT! IMPOR TANT! The machine is only designed for harvesting olive and A harvesting equipment is a dangerous tool if used fruits atached to the branches carelessly or incorrectly and can cause serious, even fatal injuries.
GENERAL SAFETY PRECA UTIONS control and the throttle lockout both move back to their BOO TS original positions. This movement is controlled by two Wear sturdy, non-slip boots. independent return springs. This arrangement means that the throttle control is automatically locked at the idle setting.
GENERAL SAFETY PRECA UTIONS Stop switch Use the stop switch to s The m is designed to keep noise l e v els to a mini m um and to direct exhaust fumes a w a y from the use r. A muffler fitted with a catalytic co nv erter is also designed to reduce harmful exhaust gases.
STARTING UP SHAFT ASSEMBLY HARNES ADJUSTMENT Introduce the shaft for the screwed area, and center with Place the lugs in the hook of the harneses, then the conical part of the machine axle. introduce the lug in the towing hook of the machine as showed in the pictures, then screw the security nuts oon the lugs.
• In order to prevent unintentional starting of the engine, • For best results and performance use HUSQVARNA the spark plug cap must always be removed during two-stroke engine oil, which is specially formulated for long-term storage, if the machine is not under close our air-cooled two-stroke engines.
FUEL HANDLING Mixing Fuelling • Always mix the petrol and oil in a clean container intended for fuel. • Always start by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix WARNING! Taking the following (shake) the fuel mixture.
STARTING AND STOPPING Check before starting Starting and stopping • Inspect the working area. Remove any objects that WARNING! The complete clutch cover could be thrown out. and pole m fore the • Check the rubbers on the pole. Never use cracked or machine is started, otherwise the clutch damaged rubbers, damaged rubbers can cause damage can come loose and cause personal...
STARTING AND STOPPING Repeat pulling the cord until the engine starts. When the engine starts. return choke control to run position and apply full throttle ; the throttle will automatically disengage from the sta rt setting. CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended.
WORKING TECHNIQUES Important IMPORTANT! During the harvesting fruits of a relevant size and weight can hit the user and can be harmful if it is necessary take the preventive actions needed to avoid injuries to the final user. IMPORTANT! The mechanical parts of the machine can be affected during the harvesting, if the harvested branch is not flexible enough, this branches can cause a backward movement causing an unbalance of the machine.
The successives oil change has to be done every 100 hours of work, approximately 1 month of continuous work. · Recomended oil: Husqvarna SYNTHETIC HT, Quantity: 160 cc. · This operation has to be done always in the technical services authorised by Husqvarna.
• Carburettor The T-screw regulates the throttle setting at idle speed. If the T-screw is turned clockwise this gives a Your Husqvarna product has been designed and higher idle speed; turning it anti-clockwise gives a manuf rmful lower idle speed.
Page 17
MAINTENANCE Low speed jet L High speed jet H Try to the highest idle speed by turning the low speed ects the engine power, speed, jet L clockwise then anti-clockwise. When the highest temperature and fuel consumption. If the high speed jet H speed has been found, turn the low speed jet L 1/4 turn is set too lean (screwed in too far) the engine speed will anti-clockwise.
MAINTENANCE Muffl er CA UTION! Never use a machine with a defective muffler. WARNING! Mufflers fitted with catalytic converters get very hot during use and remain so for some time after stopping. This also applies at idle speed. Contact CA UTION! Some mufflers are fitted with a catalytic can result in burns to the skin.
Che c k that the spark plug is fitted with a suppressor. lter lter Always use HUSQVARNA oil, art.no.531 00 92-48. vent to make it spread evenly lter must be regula r ly cleaned to rem o v e dust through the r.
MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this Operator’s Manual.
Husqv arna AB, SE-561 82 Huskvarna, Sweden, tel +46-36-146500, declares under sole responsibility that the hardvesting equioppments Husqvarna 353O4 and 353O4 X-Series dating from 2009 serial numbers and onwards (the year is clearly stated on the rating plate followed by the serial number), comply with the requirements of the COUNCIL’S DIRECTIVE: “relating to machinery”...