Table of Contents
Advertisement
Available languages
Available languages
•
STORE IDLE POLE HEDGE TRIMMER INDOORS - When
not in use, Pole Hedge Trimmer should be stored indoors in
a dry and high or locked-up place out of reach of children.
•
MAINTAIN POLE HEDGE TRIMMER WITH CARE - Keep
cutting blades sharp and clean for best performance and
to reduce the risk of injury. Keep handles dry, clean and
free from oil and grease.
•
CHECK DAMAGED PARTS - Before further use of the Pole
Hedge Trimmer, a guard or other part that is damaged
should be carefully checked to determine that it will
operate properly and perform its intended function. Check
for alignment of moving parts, binding of moving parts,
breakage of parts, mounting and any other condition
that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced by
an authorized service center unless otherwise indicated
elsewhere in this manual.
Service
•
Tool service must be performed only by qualified
repair personnel. Service or maintenance performed
by unqualified personnel could result in a risk of injury.
See Repairs.
•
When servicing a tool, use only identical
replacement parts. Follow instructions in the
Maintenance section of this manual. Use of
unauthorized parts or failure to follow Maintenance
Instructions may create a risk of electric shock or injury.
Specific Safety Rules
•
Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring. Contact with a "live" wire
will make exposed metal parts of the tool "live" and shock
the operator.
Additional Safety Information
WARNING: Never modify the power tool or any part
of it. Damage or personal injury could result.
WARNING: ALWAYS use safety glasses. Everyday
eyeglasses are NOT safety glasses. Also use face or dust
mask if operation is dusty. ALWAYS WEAR CERTIFIED
SAFETY EQUIPMENT:
•
ANSI Z87.1 eye protection (CAN/CSA Z94.3),
•
ANSI S12.6 (S3.19) hearing protection,
•
NIOSH/OSHA/MSHA respiratory protection.
WARNING: Some dust contains chemicals known
to State of California to cause cancer, birth defects
or other reproductive harm. Some examples of these
chemicals are:
•
compounds in fertilizers,
•
compounds in insecticides, herbicides
and pesticides,
•
arsenic and chromium from chemically
treated lumber.
To reduce your exposure to these chemicals,
wear approved safety equipment such as dust
masks that are specially designed to filter out
microscopic particles.
WARNING: Use of this tool can generate and/
or disperse dust, which may cause serious and
permanent respiratory or other injury. Always use
NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure. Direct particles
away from face and body.
WARNING: Always wear proper personal hearing
protection that conforms to ANSI S12.6 (S3.19)
during use. Under some conditions and duration
of use, noise from this product may contribute to
hearing loss.
CAUTION: When not in use, place tool on its side
on a stable surface where it will not cause a
tripping or falling hazard. Some tools with a large
battery pack will stand upright but may be easily
knocked over.
•
Air vents often cover moving parts and should be
avoided. Loose clothes, jewelry or long hair can be
caught in moving parts.
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ......................... volts
Hz ....................... hertz
min ..................... minutes
or DC ...... direct current
...................... Class I Construction
(grounded)
.../min .............. per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM .................... strokes per minute
OPM .................... oscillations per
minute
A ......................... amperes
W ........................ watts
or AC ........... alternating current
BATTERIES AND CHARGERS
The battery pack is not fully charged out of the carton.
Before using the battery pack and charger, read the
safety instructions below and then follow charging
procedures outlined. When ordering replacement battery
packs, be sure to include the catalog number and voltage.
READ ALL INSTRUCTIONS
English
or AC/DC .... alternating or
direct current
...................... Class II
Construction
(double insulated)
n o ....................... no load speed
n ......................... rated speed
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation
..................... avoid staring at
light
..................... wear respiratory
protection
..................... wear eye
protection
..................... wear hearing
protection
..................... read all
documentation
IPXX .................... IP symbol
5
- Quick Links:
- Assembly and Adjustments
Hide quick links:
Advertisement
Table of Contents
