Related Manuals for Siemens VersiCharge Blue 80
Summary of Contents for Siemens VersiCharge Blue 80
- Page 1 QUICK START INSTALLATION GUIDE VersiCharge Blue ™ Electric vehicle supply equipment April 2024 usa.siemens.com/versicharge...
-
Page 2: Table Of Contents
VersiCharge Blue™ 80 Quick Start Guide Table of Contents Important safety instructions Hardware kit and additional tools Remove the EVSE from packaging Mounting the bracket Mounting the charger base to the wall bracket Wiring option A: bottom left entry Wiring option B: rear entry Set the maximum current switch Close the charger... -
Page 3: Important Safety Instructions
VersiCharge Blue™ 80 Quick Start Guide Important safety instructions Symbols indicating hazards This manual contains notices you must observe to ensure your personal safety as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol. These notices are shown below: The addition of either symbol to a “Danger”... - Page 4 VersiCharge Blue™ 80 Quick Start Guide Environmental Considerations • The maximum rated ambient temperature of this device is 122°F (50°C). • This equipment should be installed at least 18 inches above floor or ground level. • To maintain Type 4 enclosure rating, use listed conduit fitting rated Type 4 or 4X. Wiring Information DANGER Hazardous Voltage.
-
Page 5: Hardware Kit And Additional Tools
Screw, M4 x 0.7 x 14mm, pan head, Torx (T20), 2mm pilot point, steel (W505564-S450) Lag screw, flanged hex head, 3/8 x 2-1/2”, zinc plated or galvanized (holster) Label - installed output rating sheet Quick Start Guide - Siemens 80A Plug, liquid tight, 1” NPT Nut, liquid tight, 1” NPT... -
Page 6: Remove The Evse From Packaging
VersiCharge Blue™ 80 Quick Start Guide Mount the EVSE holster ④ and decorative cover ②. Exercise caution to STEP 1 Figure 1 Remove all components from the packaging. Set aside the Remove the EVSE ensure that the holster and decorative cover do not get from packaging scratched. -
Page 7: Mounting The Charger Base To The Wall Bracket
VersiCharge Blue™ 80 Quick Start Guide STEP 3 Figure 4 Using the T-20 torque drive, remove the two (2) screws to detach the main cover from the EVSE. Retain the screws, Detach the setting them aside in a safe location. structural cover STEP 3B Figure 5... -
Page 8: Wiring Option A: Bottom Left Entry
VersiCharge Blue™ 80 Quick Start Guide Wiring option A: bottom left entry STEP 1 Figure 7 DANGER Install 1” NPT flexible conduit and Hazardous Voltage. Will cause death or serious injury fitting Turn off power before working on this equipment, voltage could cause injury or death. -
Page 9: Wiring Option B: Rear Entry
VersiCharge Blue™ 80 Quick Start Guide Wiring option B: rear entry STEP 1 Figure 9 Locate the sealing plug and install it to the base of the charger. Place the nut on the inside of the enclosure and Remove the factory torque to a value of 75 to 80 in-lbs. - Page 10 VersiCharge Blue™ 80 Quick Start Guide STEP 3 Figure 11 DANGER Install the wires Hazardous Voltage. Will cause death or serious injury Turn off power before working on this equipment, voltage could cause injury or death. Extreme caution is required when servicing or installing the equipment referenced.
-
Page 11: Set The Maximum Current Switch
VersiCharge Blue™ 80 Quick Start Guide Set the maximum current switch DANGER Hazardous Voltage. Will cause death or serious injury. Turn off power before working on this equipment. The voltage present could cause injury or death. Extreme caution is required when servicing or installing the equipment referenced. - Page 12 VersiCharge Blue™ 80 Quick Start Guide Jk;lhio;hjk;hjlhjl Switch Position Adjusted Amperage Rating Branch Circuit Amperage Rating Table 4 Branch circuit amperage ratings should be in accordance with local codes.
-
Page 13: Close The Charger
VersiCharge Blue™ 80 Quick Start Guide Close the charger (Optional) Route Figure 12 If the unit is equipped with Ethernet communications, the Ethernet cable locate the factory-installed 16mm liquid tight sealing plug on the bottom of the unit. Pierce the membrane and feed approximately 12”... - Page 14 VersiCharge Blue™ 80 Quick Start Guide STEP 2 Figure 15 DANGER Replace the struc- Hazardous Voltage. tural cover Will cause death or serious injury Turn off power before working on this equipment. The voltage present could cause injury or death. Extreme caution is required when servicing or installing the equipment referenced.
- Page 15 Download the free Sifinity Go mobile app available in the Google Play Store and Apple App Store. NOTICE Refer to the full VersiCharge Blue 80 installation manual for full operations and maintenance instructions and to the post installation guide for post information, both available at following QR code:...
- Page 16 This document contains a general description of available technical options only and its effectiveness will be subject to specific variables, Siemens Industry, Inc. including field conditions and project parameters. Siemens does not 3617 Parkway Ln. make representations, warranties or assurances as to the accuracy or Peachtree Corners, GA 30092 completeness of the content contained herein.